Re: [CAD_CAM_EDM_DRO] German help

Hi, well it could very well be,although it looks like a ultra-sonic head as
it has the typical radius reduced shaft towards the output end, and a space
near the output end just like the older Branson us welders i used to play
with. also the input cable connector looks like pl-259 except it has 2 pins
not 1. Branson=deftness those old welders were hell on ears..2 kw output
with almost no shielding...tnx cul brian f.

----- Original Message -----
From: "Hugh Prescott" <hugh@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, October 02, 2001 11:03 PM
Subject: Re: [CAD_CAM_EDM_DRO] German help


> How about a pressure transducer
>
> Hugh
>
> ----- Original Message -----
> From: "brian" <ka1bbg1@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Tuesday, October 02, 2001 8:22 PM
> Subject: [CAD_CAM_EDM_DRO] German help
>
>
> > Hi gang, i have a device on the end of a cable, i think it might be an
> ultrasonic head but it does have perhaps German writing on it. it's as
> follows;
> > Nicht autoklavieren
> > Nicht in losung einlegen
> > Gas-Sterilisation moglich
> > It looks like a ultrasonic head with what appears to be a fitting for
gas
> on one end and the other looks like something screwed into it. thanks,
brian
> f.
> >
> >
> > [Non-text portions of this message have been removed]
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: jmelson@... timg@... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >
> >
> >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>