Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
Posted by
ccs@m...
on 2001-11-03 10:35:57 UTC
> So, before I go off on a tangent, I thought I would ask the group forCarbide works fine - just feed really lightly until you get under the
> comments on any of 1) genral process using carbide and tool post grinder
> on ball screws, 2) use of tool post grinders & 3) if anyone has any
> experience with these particular plans.
thread. Hardest part is holding the screw - one isn't supposed to use
the crest diameter of a rolled screw as a reference surface. I did
anyway, but there were those who suggest a 4-jaw chuck and carefully
indicating on the minor diameter.
I'd say try machining the bearing diameter a bit oversize and see how
good you can get it, then decide if you need to build the grinder -
except that if you are going to do it, you probably want to do it all
in one go without removing the screw from the lathe.
Chris
Discussion Thread
carlcnc@e...
2001-10-27 16:07:10 UTC
routing plexiglass/acrylic
cncdxf@a...
2001-10-27 16:17:08 UTC
Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 18:02:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
cncdxf@a...
2001-10-27 18:18:39 UTC
Re: routing plexiglass/acrylic
cncdxf@a...
2001-10-27 18:27:08 UTC
Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 18:46:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 19:00:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
cncdxf@a...
2001-10-27 19:01:59 UTC
Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 19:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
zeff1015@a...
2001-10-29 06:04:05 UTC
Re: [CAD_CAM_EDM_DRO] routing plexiglass/acrylic
currinh@O...
2001-11-03 10:13:24 UTC
Machinig Ball Screws
ccs@m...
2001-11-03 10:35:57 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
motionin@a...
2001-11-03 18:42:42 UTC
Re: Machinig Ball Screws
munro@a...
2001-11-03 18:48:31 UTC
Re: Machinig Ball Screws
machines@n...
2001-11-04 02:55:06 UTC
Re: Machinig Ball Screws
Les Watts
2001-11-04 05:40:06 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
JanRwl@A...
2001-11-04 19:11:21 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
David M. Munro
2001-11-05 05:45:13 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws