Re: [CAD_CAM_EDM_DRO] routing plexiglass/acrylic
Posted by
zeff1015@a...
on 2001-10-29 06:04:05 UTC
We cut Corian (An Acrylic Resin based material) @ 16000 RPM on a 3 1/4 HP
router. As single flute bit will cut very fast, but give you a rough cut,
for smooth cuts use a 2 flute bit. Many production router bits have a 15
degree down-shear design. Make sure that the router bit is carbide tipped,
not solid carbide (The carbide tips seem to leave a small gap so the cutter
doesn't get gumed up). There are also spiral flute designs for CNC machines.
The best place to look for router bits is in an Armana catalog, they have a
large selection for plastics, and they are good quality bits.
Hope this helps,
Jeff
router. As single flute bit will cut very fast, but give you a rough cut,
for smooth cuts use a 2 flute bit. Many production router bits have a 15
degree down-shear design. Make sure that the router bit is carbide tipped,
not solid carbide (The carbide tips seem to leave a small gap so the cutter
doesn't get gumed up). There are also spiral flute designs for CNC machines.
The best place to look for router bits is in an Armana catalog, they have a
large selection for plastics, and they are good quality bits.
Hope this helps,
Jeff
Discussion Thread
carlcnc@e...
2001-10-27 16:07:10 UTC
routing plexiglass/acrylic
cncdxf@a...
2001-10-27 16:17:08 UTC
Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 18:02:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
cncdxf@a...
2001-10-27 18:18:39 UTC
Re: routing plexiglass/acrylic
cncdxf@a...
2001-10-27 18:27:08 UTC
Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 18:46:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 19:00:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
cncdxf@a...
2001-10-27 19:01:59 UTC
Re: routing plexiglass/acrylic
JanRwl@A...
2001-10-27 19:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: routing plexiglass/acrylic
zeff1015@a...
2001-10-29 06:04:05 UTC
Re: [CAD_CAM_EDM_DRO] routing plexiglass/acrylic
currinh@O...
2001-11-03 10:13:24 UTC
Machinig Ball Screws
ccs@m...
2001-11-03 10:35:57 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
motionin@a...
2001-11-03 18:42:42 UTC
Re: Machinig Ball Screws
munro@a...
2001-11-03 18:48:31 UTC
Re: Machinig Ball Screws
machines@n...
2001-11-04 02:55:06 UTC
Re: Machinig Ball Screws
Les Watts
2001-11-04 05:40:06 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
JanRwl@A...
2001-11-04 19:11:21 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws
David M. Munro
2001-11-05 05:45:13 UTC
Re: [CAD_CAM_EDM_DRO] Machinig Ball Screws