CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Slot drills

Posted by Les Newell
on 2001-11-17 23:21:21 UTC
Basically it looks like slot drill = ukspeak for centre cutting end mill.

Les


> Better to be busy than sitting around with nothing to do.
>
> You CAN plunge drill with and end mill...provided you use a center cutting
> end mill. I do it all the time.
> You just have to be careful with feed rate and RPM for the material being
> "drilled".
>
> Smoke
>
> > Hey Smoke,
> > Things have been good but too busy here. Regarding slot drills, I
> > think Les Newell got the description right with:
> >
> > Slot drills are two flute cutters that can plunge (drill) as well as
> > cut sideways (slot). An end mill usually has more flutes and cannot
> > plunge because there are no cutting edges in the centre of the face.
> >
> >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

dan.eaton@c... 2001-11-17 12:10:38 UTC Slot drills Les Newell 2001-11-17 13:12:11 UTC Re: [CAD_CAM_EDM_DRO] Slot drills dave_pearson@b... 2001-11-17 13:17:27 UTC Re: Slot drills Smoke 2001-11-17 16:43:51 UTC Re: [CAD_CAM_EDM_DRO] Slot drills dan.eaton@c... 2001-11-17 17:29:28 UTC Re: Slot drills Smoke 2001-11-17 18:41:56 UTC Re: [CAD_CAM_EDM_DRO] Re: Slot drills JanRwl@A... 2001-11-17 19:06:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Slot drills William Scalione 2001-11-17 21:07:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Slot drills Jon Elson 2001-11-17 21:19:27 UTC Re: [CAD_CAM_EDM_DRO] Slot drills Jon Elson 2001-11-17 21:24:10 UTC Re: [CAD_CAM_EDM_DRO] Slot drills Les Newell 2001-11-17 23:21:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Slot drills JanRwl@A... 2001-11-18 18:34:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Slot drills William Scalione 2001-11-19 04:46:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Slot drills Peter Homann 2001-11-28 16:12:44 UTC GE 1/6 HP motor wiring Problem.