CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys

Posted by Ian Wright
on 2001-11-25 07:08:06 UTC
----- Original Message -----
From: <machines@...>

> true radius. I wonder if they sent you the correct pulley's for the
> belt type ?

I don't know although I did buy them direct from their place and watched
while the fellow looked them up on his computer. When I saw how the pulleys
were made I was delighted - I wasn't looking forward to making the form tool
and setting it up accurately on that fairly small size. I suppose that using
a round bottomed slot provides relief at the bottom while allowing for a
close drive on the flanks with good contact on the top of the 'teeth'.
Making the pulleys was easy as I just had to put a couple of 2mm drills in
the slots on opposite sides of the pulley and measure across them - subtract
2mm and I had the hole circle diameter, then measure the actual OD to know
what to turn it back to.
If these pulleys are more suited to HTD belts only, perhaps it would be
useful for people making their own machines to consider using thas type of
belt.

Ian
--
Ian W. Wright
Sheffield UK
www.iw63.freeserve.co.uk

Discussion Thread

wanliker@a... 2001-11-24 13:59:17 UTC Making Stepper Pullys machines@n... 2001-11-24 14:22:56 UTC Re: Making Stepper Pullys wanliker@a... 2001-11-24 15:29:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys machines@n... 2001-11-24 16:19:45 UTC Re: Making Stepper Pullys wanliker@a... 2001-11-24 17:09:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys Smoke 2001-11-24 20:57:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys wanliker@a... 2001-11-24 21:09:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys machines@n... 2001-11-25 03:42:02 UTC Re: Making Stepper Pullys Ian Wright 2001-11-25 03:42:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys Ian Wright 2001-11-25 03:56:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys machines@n... 2001-11-25 04:26:10 UTC Re: Making Stepper Pullys Ian Wright 2001-11-25 06:29:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys machines@n... 2001-11-25 06:44:34 UTC Re: Making Stepper Pullys Ian Wright 2001-11-25 07:08:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys Robert Bachman 2001-11-25 08:25:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys machines@n... 2001-11-25 12:24:56 UTC Re: Making Stepper Pullys Alan Marconett KM6VV 2001-11-25 15:26:22 UTC Re: Making Stepper Pullys Alan Marconett KM6VV 2001-11-25 15:32:23 UTC Re: Making Stepper Pullys machines@n... 2001-11-25 17:16:52 UTC Re: Making Stepper Pullys Alan Marconett KM6VV 2001-11-25 17:52:41 UTC Re: Making Stepper Pullys Bob Bachman 2001-11-25 19:08:56 UTC [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Paul Amaranth 2001-11-25 20:26:07 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Bill Vance 2001-11-25 21:37:42 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Jon Elson 2001-11-25 22:17:11 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Jon Elson 2001-11-25 22:23:36 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help wanliker@a... 2001-11-25 22:34:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys wanliker@a... 2001-11-25 22:46:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys Bill Vance 2001-11-25 23:26:50 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help machines@n... 2001-11-26 01:29:09 UTC Re: Making Stepper Pullys JanRwl@A... 2001-11-26 08:58:53 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Jon Elson 2001-11-26 10:06:37 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Alan Marconett KM6VV 2001-11-26 11:14:08 UTC Re: Making Stepper Pullys phrh@w... 2001-11-26 11:41:16 UTC Re: Making Stepper Pullys Bill Vance 2001-11-26 12:00:32 UTC Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help Iain Ward 2001-11-26 15:14:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys Garry & Maxine Foster 2001-11-27 10:30:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys pjwizr_1999@y... 2001-12-02 00:24:11 UTC Re: Need Encoder Hookup Help