Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Posted by
Paul Amaranth
on 2001-11-25 20:26:07 UTC
Hi Bob,
There was a 7400 series inverter chip with an open collector output
that would work, 7405? It's getting late. One of those and a resistor
hooked up to +5 and +12 would do it. I'm heading out of town for a bit
or I'd send you a diagram.
Also check out the Art of Electronics by Horowitz and Hill for some
simple circuits that would work.
Paul
Paul Amaranth | Rochester MI, USA
Aurora Group, Inc. | Systems & Software
paul@... | Unix / Windows / NT
There was a 7400 series inverter chip with an open collector output
that would work, 7405? It's getting late. One of those and a resistor
hooked up to +5 and +12 would do it. I'm heading out of town for a bit
or I'd send you a diagram.
Also check out the Art of Electronics by Horowitz and Hill for some
simple circuits that would work.
Paul
>--
> OK you techy types, help me out.
>
> I have a coule of Red Lion counters which will make dandy readouts
> for a DRO. I also have some of the famous Goldmine motors with attached
> encoders.
>
> The problem: The encoders are 5 volts and the counters are 12 volts.
> The 5 volt outputs from the encoder will not trigger the 12 volt logic
> of the counter. I need a simple circuit that will use the 5v pulses
> from the encoder to create 12v pulses for the counter.
>
> Thanks,
>
>
>
>
> Bob Bachman
>
> "It's our choices that show what we truly are,
> far more than our abilities" - A. Dumbledore
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Paul Amaranth | Rochester MI, USA
Aurora Group, Inc. | Systems & Software
paul@... | Unix / Windows / NT
Discussion Thread
wanliker@a...
2001-11-24 13:59:17 UTC
Making Stepper Pullys
machines@n...
2001-11-24 14:22:56 UTC
Re: Making Stepper Pullys
wanliker@a...
2001-11-24 15:29:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
machines@n...
2001-11-24 16:19:45 UTC
Re: Making Stepper Pullys
wanliker@a...
2001-11-24 17:09:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
Smoke
2001-11-24 20:57:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
wanliker@a...
2001-11-24 21:09:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
machines@n...
2001-11-25 03:42:02 UTC
Re: Making Stepper Pullys
Ian Wright
2001-11-25 03:42:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
Ian Wright
2001-11-25 03:56:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
machines@n...
2001-11-25 04:26:10 UTC
Re: Making Stepper Pullys
Ian Wright
2001-11-25 06:29:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
machines@n...
2001-11-25 06:44:34 UTC
Re: Making Stepper Pullys
Ian Wright
2001-11-25 07:08:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
Robert Bachman
2001-11-25 08:25:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
machines@n...
2001-11-25 12:24:56 UTC
Re: Making Stepper Pullys
Alan Marconett KM6VV
2001-11-25 15:26:22 UTC
Re: Making Stepper Pullys
Alan Marconett KM6VV
2001-11-25 15:32:23 UTC
Re: Making Stepper Pullys
machines@n...
2001-11-25 17:16:52 UTC
Re: Making Stepper Pullys
Alan Marconett KM6VV
2001-11-25 17:52:41 UTC
Re: Making Stepper Pullys
Bob Bachman
2001-11-25 19:08:56 UTC
[CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Paul Amaranth
2001-11-25 20:26:07 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Bill Vance
2001-11-25 21:37:42 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Jon Elson
2001-11-25 22:17:11 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Jon Elson
2001-11-25 22:23:36 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
wanliker@a...
2001-11-25 22:34:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
wanliker@a...
2001-11-25 22:46:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
Bill Vance
2001-11-25 23:26:50 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
machines@n...
2001-11-26 01:29:09 UTC
Re: Making Stepper Pullys
JanRwl@A...
2001-11-26 08:58:53 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Jon Elson
2001-11-26 10:06:37 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Alan Marconett KM6VV
2001-11-26 11:14:08 UTC
Re: Making Stepper Pullys
phrh@w...
2001-11-26 11:41:16 UTC
Re: Making Stepper Pullys
Bill Vance
2001-11-26 12:00:32 UTC
Re: [CAD_CAM_EDM_DRO] Need Encoder Hookup Help
Iain Ward
2001-11-26 15:14:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
Garry & Maxine Foster
2001-11-27 10:30:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making Stepper Pullys
pjwizr_1999@y...
2001-12-02 00:24:11 UTC
Re: Need Encoder Hookup Help