CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more

on 2001-12-04 21:51:00 UTC
Hi Chris,

I must have missed the original question. Are you trying to control a
solid state relay, or a relay from a pin on a parallel port? And your
software has an Mcode to use? If you'll afford me a guess, do you have
a 1K pullup to +5v on the pin? and are you trying to SINK current, not
SOURCE it? a 220 ohm resistor connected to +5 and in series with an LED
makes a good test probe. You should see the respective pin control the
LED of all is working.

This will allow you to divide the problem in two! Makes it easier to
debug.

HTH

Alan KM6VV


Chris Clough wrote:
>
> Ok - so I went and got all new components and rebuilt it twice now today
> - I'm using the schematic of off Tim's site - I built it, had two EE's
> look at it, and said that's the way it is on the page so... what's my
> next option?
> Any help - PLEASE :(
> -Chris Clough
> Xtech Engineering

Discussion Thread

Arne Chr. Jorgensen 1999-10-16 02:22:32 UTC CAD/CAM Software Jim 2000-10-18 08:08:09 UTC CAD/CAM Software Hugh Mahlendorf 2000-10-18 18:20:25 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software Darrell 2000-10-18 19:35:34 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software Hugh Mahlendorf 2000-10-18 20:37:17 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software wanliker@a... 2000-10-18 23:21:59 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software Hugh Mahlendorf 2000-10-19 16:36:58 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software Hugh Mahlendorf 2000-10-19 16:38:20 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software Doug Harrison 2000-10-19 17:41:57 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software Scott M. Thomas 2001-12-03 10:27:42 UTC [CAD_CAM_EDM_DRO] CAD/CAM Software glee@i... 2001-12-03 11:27:00 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software dave_pearson@b... 2001-12-03 11:42:59 UTC Re: CAD/CAM Software machines@n... 2001-12-03 14:41:09 UTC Re: CAD/CAM Software Gail & Bryan Harries 2001-12-03 14:49:13 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD/CAM Software glee@i... 2001-12-03 14:51:01 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD/CAM Software glee@i... 2001-12-03 14:54:49 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD/CAM Software machines@n... 2001-12-03 15:02:39 UTC Re: CAD/CAM Software machines@n... 2001-12-03 15:08:09 UTC Re: CAD/CAM Software Paul 2001-12-03 15:08:34 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD/CAM Software Fitch R. Williams 2001-12-03 19:21:49 UTC Re: [CAD_CAM_EDM_DRO] CAD/CAM Software dave_pearson@b... 2001-12-03 23:43:29 UTC Re: CAD/CAM Software machines@n... 2001-12-04 01:08:58 UTC Re: CAD/CAM Software scottle@m... 2001-12-04 15:21:23 UTC Re: CAD/CAM Software Chris Clough 2001-12-04 19:07:56 UTC Parallel Port/Relay Problems... more Tim Goldstein 2001-12-04 20:39:33 UTC RE: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Alan Marconett KM6VV 2001-12-04 21:51:00 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Jon Elson 2001-12-04 23:09:12 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Matthew King 2001-12-05 03:50:28 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more ccs@m... 2001-12-05 05:08:17 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Alan Marconett KM6VV 2001-12-05 11:22:20 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more ccs@m... 2001-12-05 11:42:55 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Alan Marconett KM6VV 2001-12-05 12:18:36 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more JanRwl@A... 2001-12-05 12:36:33 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Larry Van Duyn 2001-12-05 13:17:09 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Jon Elson 2001-12-05 22:28:55 UTC Re: [CAD_CAM_EDM_DRO] Parallel Port/Relay Problems... more Wayde C. Gutman 2004-03-23 09:14:36 UTC RE:CAD/CAM Software