RE: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Posted by
Scott M. Thomas
on 2001-12-12 19:21:53 UTC
A potentiometer will last a long time if used regularly. They tend to get
noisy faster if left unused for extended periods. I know a lot of fuel
injection systems use a pot on the end of the throttle plate shaft to sense
throttle opening and the engine compartment is a rather harsh environment.
noisy faster if left unused for extended periods. I know a lot of fuel
injection systems use a pot on the end of the throttle plate shaft to sense
throttle opening and the engine compartment is a rather harsh environment.
> -----Original Message-----
> From: Peter Seddon [mailto:peter@...]
> Sent: Monday, December 10, 2001 4:18 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear
> pot
>
>
> This is somewhat surprising as potentiometers are:
> 1. Prone to go noisey
> 2. Diffiuclt to seal against dust etc
> 3. Are contact devices and thus liable to wear
> 4. Are analogue devices and thus less accurate
> 5. The signal requires conversion to a digital signal before
> it can be used
> (unless the system is fully analogue).
>
> The only advantage would be cost
>
> Regards Peter
>
Discussion Thread
byron@w...
2001-12-09 06:30:22 UTC
Cnc PCB drilling machines z axis linear pot
JanRwl@A...
2001-12-09 20:21:20 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Randy Gordon-Gilmore
2001-12-09 23:21:35 UTC
PCB bits, was Cnc PCB drilling machines
Bill Vance
2001-12-10 00:45:05 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Peter Seddon
2001-12-10 01:23:13 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
ka1bbg
2001-12-10 05:32:20 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Krahabors
2001-12-10 06:34:20 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Bill Vance
2001-12-10 07:27:19 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Ray
2001-12-10 09:05:01 UTC
Re: Re: Cnc PCB drilling machines z axis linear pot
Jon Elson
2001-12-10 09:43:11 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
morerust
2001-12-10 11:06:33 UTC
Re: Cnc PCB drilling machines z axis linear pot
Alan Marconett KM6VV
2001-12-10 11:34:52 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Peter Seddon
2001-12-10 12:20:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Cnc PCB drilling machines z axis linear pot
Bill Vance
2001-12-10 15:17:26 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Paul Amaranth
2001-12-10 15:34:39 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
JanRwl@A...
2001-12-10 17:34:57 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
JanRwl@A...
2001-12-10 17:35:48 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
ka1bbg
2001-12-10 19:12:32 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
ka1bbg
2001-12-10 19:12:33 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Jon Elson
2001-12-10 20:57:33 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Alan Marconett KM6VV
2001-12-10 21:06:04 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Jon Elson
2001-12-10 21:07:04 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Bill Vance
2001-12-10 21:37:34 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Corey
2001-12-10 22:27:22 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Alan Marconett KM6VV
2001-12-10 23:49:41 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
ka1bbg
2001-12-11 05:50:29 UTC
Re: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot
Scott M. Thomas
2001-12-12 19:21:53 UTC
RE: [CAD_CAM_EDM_DRO] Cnc PCB drilling machines z axis linear pot