Re: Circuit Board Layout Program

Alan,

This is a gerber file of a 0.9" circle inscribed in a 0.9" square
whose lower left-hand corner was placed at the x,y origin (x=0, y=0).
Most of the code must be for the circle line segments. The numerical
data is xxx.xxxx leading zeroes and decimal point not shown. Seems it
should be possible to turn it into G-Code.

Mariss

G04 AutoGERB for AutoCAD 14/2000*
G04 RS274-X Output *
%FSLAX34Y34*%
%MOIN*%
%ADD12C,0.005000*%
%ADD13C,0.007000*%
G54D12*X10000Y5000D02*X9988Y5348D01*X9952Y5694*X9891Y6036*X9807Y6374*X
9700Y6705*X9570Y7028*X9418Y7341*X9245Y7642*X9051Y7931*X8837Y8206*X8605
Y8465*X8355Y8707*X8089Y8932*X7808Y9137*X7514Y9322*X7207Y9486*X6890Y962
9*X6563Y9749*X6229Y9847*X5889Y9920*X5545Y9970*X5198Y9996*X4850Y9998*X4
503Y9975*X4158Y9929*X3817Y9858*X3482Y9764*X3155Y9647*X2836Y9507*X2528Y
9346*X2231Y9164*X1949Y8961*X1681Y8739*X1429Y8499*X1194Y8242*X978Y7970*
X781Y7683*X604Y7383*X449Y7072*X316Y6750*X206Y6420*X119Y6083*X55Y5741*X
16Y5396*X0Y5048*X9Y4700*X42Y4354*X99Y4011*X180Y3672*X284Y3340*X410Y301
6*X560Y2702*X730Y2398*X921Y2108*X1132Y1831*X1362Y1570*X1609Y1325*X1873
Y1098*X2152Y890*X2445Y702*X2750Y535*X3066Y389*X3391Y266*X3724Y165*X406
4Y88*X4407Y35*X4754Y6*X5102Y1*X5449Y20*X5795Y64*X6136Y131*X6472Y222*X6
801Y335*X7121Y472*X7430Y630*X7728Y810*X8013Y1010*X8283Y1229*X8538Y1467
*X8775Y1721*X8994Y1992*X9193Y2277*X9373Y2575*X9531Y2885*X9667Y3205*X97
80Y3534*X9871Y3870*X9937Y4211*X9980Y4557*X10000Y5000*G54D12*X0Y0D02*X1
0000Y0D01*X10000Y10000*X0Y10000*X0Y0*M02*

--- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> Hi Brian,
>
> Yes, I ran it through my "viewer" code, and The numbers were STILL
too
> big! I divide the integers by 10000.0, for 4.2 gerber.
Which "Gerber"
> is this? 6.n? There should be an aperture file (.WHL?) to use with
this
> code. RS274X has a header with aperture info, RS274D does not.
>
> Alan KM6VV