Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Posted by
Chris L
on 2002-02-17 10:22:16 UTC
Smoke wrote:
(snip) I experimented with something then available
once..... I had a bad shaft in a Simplicity gearbox with a wobbly keyway. The
dealer said they did not have a shaft in stock so I bonded the key in to the
sloppy slot and slid the gear on. The gear was sloppy too so I put some on the
end of the shaft. I knew it was a temporary repair and planned on rebuilding the
whole unit later. Within 4 hours the dealer called me back and said he did have
a shaft. I went and picked it up, then went to press off the gear.
It would not come off with our little 20 ton press. I was afraid to put it on
something bigger. I heated the whole thing up with the torch and finally got it
off. Sure, now I had a de-tempered gear and the dealer did not have that either.
Anyhow, That Loctite is an excellent metal to metal glue. I hold Rack and pinion
sections to steel framework without any fasteners !
Chris L
(snip) I experimented with something then available
> called Loctite Bearing Mount (no longer available). I put in a few drops,Loctite 609 (or is it 906) is the same stuff. I did a foolish thing with it
> slid the bearing in and heated it with a match. After heating I couldn't
> get the bearing out even using a 3 pound ball peen hammer and a BIG punch!
once..... I had a bad shaft in a Simplicity gearbox with a wobbly keyway. The
dealer said they did not have a shaft in stock so I bonded the key in to the
sloppy slot and slid the gear on. The gear was sloppy too so I put some on the
end of the shaft. I knew it was a temporary repair and planned on rebuilding the
whole unit later. Within 4 hours the dealer called me back and said he did have
a shaft. I went and picked it up, then went to press off the gear.
It would not come off with our little 20 ton press. I was afraid to put it on
something bigger. I heated the whole thing up with the torch and finally got it
off. Sure, now I had a de-tempered gear and the dealer did not have that either.
Anyhow, That Loctite is an excellent metal to metal glue. I hold Rack and pinion
sections to steel framework without any fasteners !
Chris L
Discussion Thread
Lloyd Leung
2002-02-16 19:50:58 UTC
extrusion of Linear Bearing pillow block question...
dave_ace_me
2002-02-16 20:23:24 UTC
Re: extrusion of Linear Bearing pillow block question...
Chris L
2002-02-16 21:08:42 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
wanliker@a...
2002-02-16 21:25:56 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Marcus & Eva
2002-02-17 08:31:19 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Smoke
2002-02-17 09:23:11 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Randy Gordon-Gilmore
2002-02-17 10:04:05 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Chris L
2002-02-17 10:22:16 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Andy Olney
2002-02-17 12:50:03 UTC
RE: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
Chris L
2002-02-17 13:11:50 UTC
Re: [CAD_CAM_EDM_DRO] extrusion of Linear Bearing pillow block question...
aspaguy
2002-02-17 14:17:21 UTC
Re: extrusion of Linear Bearing pillow block question...
wanliker@a...
2002-02-17 15:15:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: extrusion of Linear Bearing pillow block question...
ballendo
2002-02-17 23:57:42 UTC
Re: extrusion of Linear Bearing pillow block question...
ballendo
2002-02-18 02:57:02 UTC
Re: extrusion of Linear Bearing pillow block question...