CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] indexing layout for larger capacity

Posted by Chris L
on 2002-02-17 20:39:30 UTC
I have even put 1/4" holes into the drawing and then subsequently machined
them into a "dead" section of the material. When I am ready to "move" or re
"index", I will drop a bit, or preferably a Dowel pin into that hole, remove my
clamps and then let the machine itself drag the material via a move command to
the new location. Works excellent, can't go wrong !. Just re-clamp and start
cutting the rest of the project. This method does not take any real extra
thinking as I have enough to think about !

I usually use a fence for alignment along the X axis, so this helps the
location issue in the undraggable direction.

Chris L

Bob Campbell wrote:

> Dale,
>
> On my cnc router I can index by creating two index points or two known
> points. Cut the first part and then move the material. I then move my
> cutter to one of the known index points and do a g92 for the known x and y
> values. I then do a move to another known index point to check if the
> material has moved off the vertical.
>
> Bob
>
> ----- Original Message -----
> From: "aspaguy" <spaguy@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Sunday, February 17, 2002 7:50 PM
> Subject: [CAD_CAM_EDM_DRO] indexing layout for larger capacity
>
> > HI list,
> > I tried to search the archives for this answer, but the term index
> > has multiple meanings in this field.
> > Plasmacam manufactures a 4'x4' plasma table, but claims to have 4'x
> > unlimited capacity because you can "index" the material and move it
> > down and resume cutting. Is this a cad or cam function, and, do I
> > need a specific programm for this or is it a feature most cad/cam
> > programs utilize?
> > Thanks, Dale
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: jmelson@... timg@... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> >
> >
> > Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
> >
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

aspaguy 2002-02-17 17:50:39 UTC indexing layout for larger capacity Chris L 2002-02-17 17:59:56 UTC Re: [CAD_CAM_EDM_DRO] indexing layout for larger capacity aspaguy 2002-02-17 18:13:02 UTC Re: indexing layout for larger capacity Bob Campbell 2002-02-17 18:15:39 UTC Re: [CAD_CAM_EDM_DRO] indexing layout for larger capacity Chris L 2002-02-17 20:39:30 UTC Re: [CAD_CAM_EDM_DRO] indexing layout for larger capacity Raymond Heckert 2002-02-17 21:46:27 UTC Re: [CAD_CAM_EDM_DRO] indexing layout for larger capacity ballendo 2002-02-18 02:01:23 UTC Paneling output was Re: indexing layout for larger capacity imserv1 2002-02-18 07:28:57 UTC Paneling output was Re: indexing layout for larger capacity