Re: TypeMatic Rate
Posted by
fast1994gto
on 2002-02-21 00:03:47 UTC
Alan,
See message
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/message/40186
posted this morning.
"out" is an x86 command that puts a byte out on a port. "in" reads.
I would have to look up the hex op codes. In general it looks
something like this:
out 70h, 13h ; set up to read the NVRAM offset 13h
in 70h, ax ; read the byte
Here it is in (ugh) BASIC:
10 30 OUT &H70, &H13
20 PRINT HEX$(INP(&H71));
70h and 71h are the i/o ports that access the NVRAM. You should eb
able to write to the location using out 71h, ax (or some equivalent).
Barry
See message
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/message/40186
posted this morning.
"out" is an x86 command that puts a byte out on a port. "in" reads.
I would have to look up the hex op codes. In general it looks
something like this:
out 70h, 13h ; set up to read the NVRAM offset 13h
in 70h, ax ; read the byte
Here it is in (ugh) BASIC:
10 30 OUT &H70, &H13
20 PRINT HEX$(INP(&H71));
70h and 71h are the i/o ports that access the NVRAM. You should eb
able to write to the location using out 71h, ax (or some equivalent).
Barry
--- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> Hi Barry,
>
> How about "E1200:00" (in Debug) to enter values in memory? First we
> need to know WHERE they are! ;>)
>
> What is "out assembler"?
>
> Alan KM6VV
>
>
> fast1994gto wrote:
> >
> > You use the out assembler command to twiddle with these memory
> > locations.
> >
> > Barry
> >
> > --- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...>
wrote:
> > > Hi Jerry,
> > >
> > > I didn't see any "get" typematic rate command in Phoenix's BIOS
> > book.
> > > It might be at a defined location in the BIOS RAM (40:), but I
> > didn't
> > > see it called out.
Discussion Thread
Carol & Jerry Jankura
2002-02-20 05:34:04 UTC
TypeMatic Rate
fast1994gto
2002-02-20 06:48:06 UTC
Re: TypeMatic Rate
Alan Marconett KM6VV
2002-02-20 11:27:11 UTC
Re: [CAD_CAM_EDM_DRO] TypeMatic Rate
Alan Marconett KM6VV
2002-02-20 13:58:24 UTC
Re: TypeMatic Rate
fast1994gto
2002-02-20 17:34:33 UTC
Re: TypeMatic Rate
Alan Marconett KM6VV
2002-02-20 18:32:28 UTC
Re: TypeMatic Rate
fast1994gto
2002-02-21 00:03:47 UTC
Re: TypeMatic Rate
Alan Marconett KM6VV
2002-02-21 11:40:02 UTC
Re: TypeMatic Rate
Bert Pirson
2002-02-21 12:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: TypeMatic Rate
Carol & Jerry Jankura
2002-02-21 13:50:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: TypeMatic Rate
Alan Marconett KM6VV
2002-02-21 13:57:01 UTC
Re: TypeMatic Rate
ballendo
2002-02-22 04:00:00 UTC
BASIC, yes! was Re: TypeMatic Rate
Carol & Jerry Jankura
2002-02-22 05:53:27 UTC
RE: [CAD_CAM_EDM_DRO] BASIC, yes! was Re: TypeMatic Rate
JanRwl@A...
2002-02-22 23:17:58 UTC
Re: [CAD_CAM_EDM_DRO] BASIC, yes! was Re: TypeMatic Rate
Carol & Jerry Jankura
2002-02-23 05:37:03 UTC
RE: [CAD_CAM_EDM_DRO] BASIC, yes! was Re: TypeMatic Rate
ballendo
2002-02-23 06:10:50 UTC
BASIC, yes! was Re: TypeMatic Rate