Re: Horizontal
Posted by
stevenson_engineers
on 2002-02-22 05:25:42 UTC
--- In CAD_CAM_EDM_DRO@y..., "Mark Ehle" <ehlem@c...> wrote:
meat designed in and the overarm support counts a lot.
I have a Victoria U2, same as the Elliot U2.
Bed size is 11" x 45" just a bit smaller than a bridgeport but it has
a useable travel of 30" which is a lot more than a bridgy.
I use this for doing toolholders for North Sea boring rigs.
Two 7/8" wide cutters, 1/2" spaced and 1.125" depth of cut, straight
thru in one pass, chips every where {g}
To make any vertical more rigid when using horizontal type cutters
take a look at the picture on my home page.
http://homepage.ntlworld.com/machines/vertical%20support.jpg
Self explanitary, just build to suit the machine in question.
John S.
> I've got 2 - a Milwaukee #3 and an old I-don't-know-what with a B&SHorizontals are far mor rigid than verticals. Most have a lot more
>#11 taper. I have always liked their rigidity ever since I learned
>how to use one in high school.
meat designed in and the overarm support counts a lot.
I have a Victoria U2, same as the Elliot U2.
Bed size is 11" x 45" just a bit smaller than a bridgeport but it has
a useable travel of 30" which is a lot more than a bridgy.
I use this for doing toolholders for North Sea boring rigs.
Two 7/8" wide cutters, 1/2" spaced and 1.125" depth of cut, straight
thru in one pass, chips every where {g}
To make any vertical more rigid when using horizontal type cutters
take a look at the picture on my home page.
http://homepage.ntlworld.com/machines/vertical%20support.jpg
Self explanitary, just build to suit the machine in question.
John S.
Discussion Thread
bswim_99
2002-02-21 09:32:05 UTC
Horizontal
John H.
2002-02-21 10:02:27 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal
Smoke
2002-02-21 11:56:27 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal
Brian
2002-02-21 20:07:10 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal
ballendo
2002-02-22 04:25:09 UTC
Re: Horizontal
Mark Ehle
2002-02-22 04:34:03 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal
Dr Brian H Le Page
2002-02-22 05:14:42 UTC
Servo Motor Identification
stevenson_engineers
2002-02-22 05:25:24 UTC
Re: Horizontal
stevenson_engineers
2002-02-22 05:25:42 UTC
Re: Horizontal
Mark Ehle
2002-02-22 05:30:51 UTC
[CAD_CAM_EDM_DRO] Re: Horizontal
A. G. Eckstein
2002-02-22 05:34:41 UTC
Re: [CAD_CAM_EDM_DRO] Servo Motor Identification
Sven Peter
2002-02-22 05:37:37 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal
Greg Pettengill
2002-02-22 06:03:43 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal
j.guenther
2002-02-22 08:11:49 UTC
RE: [CAD_CAM_EDM_DRO] Horizontal
Sven Peter
2002-02-22 16:48:10 UTC
Re: [CAD_CAM_EDM_DRO] Horizontal