RE: [CAD_CAM_EDM_DRO] Re: Ultimate free CAD system?

No
You do have to save the code incase you do install again later but
the same code will even work on multiple computers though I am sure
they would appreciate it if you didn't do this. But using the same
key on a later reinstall shouldn't be a problem.

The only problem I had is the registration process is a bit of a
hassle and the site wasn't working the first time I tried. You have
to register with the company before you can register the software.

Garry

To: CAD_CAM_EDM_DRO@yahoogroups.com
From: dlantz@...
Date sent: Mon, 25 Feb 2002 15:23:59 -0500
Subject: RE: [CAD_CAM_EDM_DRO] Re: Ultimate free CAD system?
Send reply to: CAD_CAM_EDM_DRO@yahoogroups.com

> my memory is a bit fuzzy on this (it was awhile ago) but i seem to remember
> having to get a registration code every time i load the software. now with
> windows... that can be every two weeks! if the company were to go out of
> bussiness, i would be out of luck.---Dave
>
> -----Original Message-----
> From: imserv@... [mailto:imserv@...]
> Sent: Monday, February 25, 2002 8:10 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: Ultimate free CAD system?
>
>
> --- In CAD_CAM_EDM_DRO@y..., dlantz@a... wrote:
> > i tried the pro/DEsk too, it seemed very powerfull also, however the
> > licencing thing was too constrictive for me
>
> Can you explain that a little more Dave? I am concerned that you
> noticed something that I might have missed. The only thing that stuck
> in my mind was restrictions to exporting to certain countries on the
> USA bad boy list.
>
>
> Best Regards,
>
> Fred Smith
> IMService
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> http://www.metalworking.com/news_servers.html
> http://www.metalworking.com/news_servers.html
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> http://www.metalworking.com/news_servers.html
> http://www.metalworking.com/news_servers.html
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>