CAD CAM EDM DRO - Yahoo Group Archive

Re: DIACRO BENDER QUESTION

Posted by doug98105
on 2002-03-12 07:26:17 UTC
Stan,

No I haven't made any dies specifically for the Diacro. I have used
tube bending dies from another bender in the Diacro. They fit
because both machines have a 1" diameter center hole.

Starter motor? Hadn't thought of that, are they rated for continuous
duty? Don't they draw very high amperage, 50+ amps?

Thanks for the offer of the manual, I have the printed version which
covers general bending techniques for all the benders. Is that the
same thing you have on disk?

Doug

--- In CAD_CAM_EDM_DRO@y..., stan mcdonald <SMCDONAL@K...> wrote:
> Have you made any dies for bending tube?
> Do you need the manaul for the #3 bender if so I have it on disk.
> Regards
> Stan
>
>
> doug98105 wrote:
>
> > Stan,
> >
> > I'm pretty sure everything is the same except the #4 has the
> > mechanical advantage of the ratchet action.
> >
> > To get this on topic.....I've thought about wrapping a chain
around
> > the base of my #3 so it's like a #4. Then adding a motorized
drive
> > in place of the ratchet mechanism with the degree of rotation and
> > work clamping under computer control. The intention is to come up
> > with an automated bender.
> >
> > So far I haven't come up with an easy solution to the torque
> > requirements of the drive motor, other than using an hydraulic
> > motor.
> >
> > Doug
> >
> > --- In CAD_CAM_EDM_DRO@y..., stan mcdonald <SMCDONAL@K...> wrote:
> > > Can someone here tell me if a #4 Diacro Bender is larger in DIA
> > then a
> > > #3 or are they the same size? I am looking to find out if the
dia
> > of the
> > > round part is bigger?
> > > The mad RAD is the same and so is the leverage so other then the
> > ratchet
> > > whats the difference between a 3 and a 4?
> > >
> > > Thanks
> > > Stan
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > OFF Topic POSTS: General Machining
> > http://www.metalworking.com/news_servers.html
> > http://www.metalworking.com/news_servers.html
> >
> > Post messages: CAD_CAM_EDM_DRO@y...
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Discussion Thread

stan mcdonald 2002-03-08 20:30:04 UTC DIACRO BENDER QUESTION doug98105 2002-03-08 23:00:31 UTC Re: DIACRO BENDER QUESTION Jay Hayes 2002-03-09 07:48:20 UTC Re: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION Lloyd Leung 2002-03-09 09:27:49 UTC RE: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION stan mcdonald 2002-03-12 00:08:02 UTC Re: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION stan mcdonald 2002-03-12 00:09:32 UTC Re: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION doug98105 2002-03-12 07:26:17 UTC Re: DIACRO BENDER QUESTION Sven Peter 2002-03-12 16:19:52 UTC Re: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION jim davies 2002-03-12 18:19:59 UTC Re: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION