Re: [CAD_CAM_EDM_DRO] Re: DIACRO BENDER QUESTION

Starter motor. On my 1960 wilies with 6 V Baterie it pulls 370A
Nice hit isn't it?
Sven Peter

doug98105 wrote:

>
> Stan,
>
> No I haven't made any dies specifically for the Diacro. I have used
> tube bending dies from another bender in the Diacro. They fit
> because both machines have a 1" diameter center hole.
>
> Starter motor? Hadn't thought of that, are they rated for continuous
> duty? Don't they draw very high amperage, 50+ amps?
>
> Thanks for the offer of the manual, I have the printed version which
> covers general bending techniques for all the benders. Is that the
> same thing you have on disk?
>
> Doug
>
> --- In CAD_CAM_EDM_DRO@y..., stan mcdonald <SMCDONAL@K...> wrote:
> > Have you made any dies for bending tube?
> > Do you need the manaul for the #3 bender if so I have it on disk.
> > Regards
> > Stan
> >
> >
> > doug98105 wrote:
> >
> > > Stan,
> > >
> > > I'm pretty sure everything is the same except the #4 has the
> > > mechanical advantage of the ratchet action.
> > >
> > > To get this on topic.....I've thought about wrapping a chain
> around
> > > the base of my #3 so it's like a #4. Then adding a motorized
> drive
> > > in place of the ratchet mechanism with the degree of rotation and
> > > work clamping under computer control. The intention is to come up
> > > with an automated bender.
> > >
> > > So far I haven't come up with an easy solution to the torque
> > > requirements of the drive motor, other than using an hydraulic
> > > motor.
> > >
> > > Doug
> > >
> > > --- In CAD_CAM_EDM_DRO@y..., stan mcdonald <SMCDONAL@K...> wrote:
> > > > Can someone here tell me if a #4 Diacro Bender is larger in DIA
> > > then a
> > > > #3 or are they the same size? I am looking to find out if the
> dia
> > > of the
> > > > round part is bigger?
> > > > The mad RAD is the same and so is the leverage so other then the
> > > ratchet
> > > > whats the difference between a 3 and a 4?
> > > >
> > > > Thanks
> > > > Stan
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > >
> > > OFF Topic POSTS: General Machining
> > > http://www.metalworking.com/news_servers.html
> > > http://www.metalworking.com/news_servers.html
> > >
> > > Post messages: CAD_CAM_EDM_DRO@y...
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > Moderator: jmelson@a... timg@k... [Moderator]
> > > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > bill,
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> http://www.metalworking.com/news_servers.html
> http://www.metalworking.com/news_servers.html
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/