CAD CAM EDM DRO - Yahoo Group Archive

Re: Matching Microsteps to moters

Posted by aspaguy
on 2002-04-02 20:42:45 UTC
Thanks for the suggestion, but my first step was to contact
compumoter. They confirmed that these drives could not be modified
for my purposes.
Dale


--- In CAD_CAM_EDM_DRO@y..., "Carol & Jerry Jankura"
<jerry.jankura@s...> wrote:
> Hi, Dale:
>
> Although I'm not the expert that Mariss and the others are, I've
worked with
> Compumotors a few years back. I was told that the motor's basic
step rate is
> the same 200 step per rev that many of the others are, but that the
motors
> are manufactured to close tolerances and matched to the controller.
>
> Regarding your X language controllers? Does Compumotor make a
similar
> motor/controller that uses step and direction? If so, you might be
able to
> swap the EProms in your driver for EProms from a Step/Direction
drive. We
> once worked with our local Compumotor rep to get EProms to change
an RS-232
> interface controller to Step/Dir. It might work for you.
>
> -- Jerry
>
> |-----Original Message-----
> |From: aspaguy [mailto:spaguy@l...]
> |Sent: Tuesday, April 02, 2002 1:24 AM
> |To: CAD_CAM_EDM_DRO@y...
> |Subject: [CAD_CAM_EDM_DRO] Matching Microsteps to moters
> |
> |
> |Hi Jon, Tim, Mariss, others,
> |All this talk about microstep accuracy and smoothness has gotten me
> |thinking about my compumoter steppers. My Moters are compumoter c
> |series which came as part of a package which included the moters
and
> |cx drivers, which I can't use for my project since they use
> |compumoter X language instead of step & direction signals. They may
> |have provided me with a valuable piece of info however. These
drivers
> |are 12800 microstep drives. The Geckos are as I understand it are
> |2000 microstep drives (200 steps x 10 micro per step if I'm
thinking
> |correctly). This didn't concern me untill now as I have heard so
much
> |about how smooth the geckos make your machine perform. Now I see
that
> |Tims API drives have a 12800 setting, and after reading the
previous
> |posts I wonder if these might run smoother with my moters that were
> |designed to run with 12800 microsteps. Will my moters run poorly
with
> |Geckos? With everything Mariss does here, including designing
> |circuits for plasma controls etc. I prefer to purchase Geckos, But
if
> |my moters are not going to like them, maybe I should grab some APIs
> |while I can, and next time purchase moters that will be compatable
> |with geckos.
> |Any Thoughts from the experts?
> |Thanks, Dale
> |
> |
> |Addresses:
> |FAQ: http://www.ktmarketing.com/faq.html
> |FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> |
> |OFF Topic POSTS: General Machining
> |If you wish to post on unlimited OT subjects goto:
> |aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> |reach it if you have trouble.
> |http://www.metalworking.com/news_servers.html
> |
> |http://groups.yahoo.com/group/jobshophomeshop I consider this as
> |a sister site to the CCED group, as many of the same memembers are
> |there, for OT subjects, that are not allowed on the CCED list.
> |
> |
> |
> |Post messages: CAD_CAM_EDM_DRO@y...
> |Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> |Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> |List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> |Moderator: jmelson@a... timg@k... [Moderator]
> |URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> |bill,
> |List Mom
> |List Owner
> |
> |
> |
> |Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> |
> |
> |
> |

Discussion Thread

aspaguy 2002-04-01 22:24:24 UTC Matching Microsteps to moters William Scalione 2002-04-02 05:36:53 UTC Re: [CAD_CAM_EDM_DRO] Matching Microsteps to moters Carol & Jerry Jankura 2002-04-02 06:49:33 UTC RE: [CAD_CAM_EDM_DRO] Matching Microsteps to moters Jon Elson 2002-04-02 10:43:17 UTC Re: [CAD_CAM_EDM_DRO] Matching Microsteps to moters aspaguy 2002-04-02 20:42:45 UTC Re: Matching Microsteps to moters aspaguy 2002-04-02 20:48:35 UTC Re: Matching Microsteps to moters aspaguy 2002-04-03 19:47:26 UTC Re: Matching Microsteps to moters Mariss? TimG? Ballendo? aspaguy 2002-04-03 19:48:24 UTC Re: Matching Microsteps to moters