CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Servos

Posted by RC
on 2002-06-14 13:36:57 UTC
Frank, if you don't mind sharing with us, what does your servo system
consist of? I too would like to build a servo system for the same reasons,
and any information would be very helpful in getting me started.....

RC
----- Original Message -----
From: dakota8833 <dakota8833@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, June 14, 2002 7:44 AM
Subject: [CAD_CAM_EDM_DRO] Servos


> After playing around with a stepper system for months and trying to
> resolve lost or gained step problems I gave up.
> What I found with open loop steppers is that on some nc files I would
> see this. Now I'm running servos and never looked back.
> Other members have listed pros and cons of either method. This is why
> I would go servo ,... For one, no worry of lost position
> from part to part. I ran 12 rudder cores at 2 hrs a piece. I'm going
> to redesign my mill making it more robust. Belt driving 4 to 1
> using my current 1 inch lead screw to get the torque I need. In doing
> this I will be able to mill denser material and take larger cuts
> at speed. Typically servos run at a much higher rpm and you don't
> loose the torque one is trying to gain by "gear reduction". And
> with a servo ( encoders ) I can change to a lower resolution and
> maintain my current 2048 cpr. at .0005. CPU load stays the
> same and I don't push my control software either. I think steppers are
> fine for small mills where speed is not important but for
> large router tables servos are the way to go .
>
> Frank
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

Jon Elson 2000-11-02 16:17:41 UTC Re: Servos Ian Wright 2001-08-21 03:28:53 UTC Servos Jon Elson 2001-08-21 09:19:35 UTC Re: [CAD_CAM_EDM_DRO] Servos Ian Wright 2001-08-21 09:48:58 UTC Re: [CAD_CAM_EDM_DRO] Servos dakota8833 2002-06-14 07:44:15 UTC Servos RC 2002-06-14 13:36:57 UTC Re: [CAD_CAM_EDM_DRO] Servos dakota8833 2002-06-17 17:30:24 UTC Re: Servos/help machinist24540 2002-11-08 11:38:05 UTC Servos Mark 2002-11-08 22:22:59 UTC Re: Servos Jon Elson 2002-11-08 23:03:18 UTC Re: [CAD_CAM_EDM_DRO] Servos William Scalione 2002-11-11 11:50:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Servos