Re: [CAD_CAM_EDM_DRO] steppers
Posted by
Joll503@A...
on 2002-07-11 01:32:19 UTC
Wouldn't a latch allow the best of both worlds?
In a message dated 7/10/02 10:25:19 PM Central Daylight Time,
elson@... writes:
<<
The series connection has minute advantage over the parallel in holding
torque
at standstill, but suffers vastly in speed. The series connection has 4 x
the
inductance of a single winding, and the parallel has 1/4th the inductance of
single, so you end up with 1/16th the inductance in parallel, thereby
allowing
the motor to run 16 times faster in parallel.
(At least, it seems like it should work that way as separate coils on the
same
magnetic components.)
In a message dated 7/10/02 10:25:19 PM Central Daylight Time,
elson@... writes:
<<
The series connection has minute advantage over the parallel in holding
torque
at standstill, but suffers vastly in speed. The series connection has 4 x
the
inductance of a single winding, and the parallel has 1/4th the inductance of
single, so you end up with 1/16th the inductance in parallel, thereby
allowing
the motor to run 16 times faster in parallel.
(At least, it seems like it should work that way as separate coils on the
same
magnetic components.)
>>
Discussion Thread
Gene
2002-07-10 00:00:20 UTC
steppers
stevenson_engineers
2002-07-10 00:56:02 UTC
Re: steppers
Tim Goldstein
2002-07-10 09:31:51 UTC
Re: [CAD_CAM_EDM_DRO] steppers
Jon Elson
2002-07-10 10:08:32 UTC
Re: [CAD_CAM_EDM_DRO] steppers
Steve Blackmore
2002-07-10 11:55:19 UTC
Re: [CAD_CAM_EDM_DRO] steppers
Jon Elson
2002-07-10 20:24:00 UTC
Re: [CAD_CAM_EDM_DRO] steppers
Gene
2002-07-11 00:11:10 UTC
steppers
Gene
2002-07-11 00:44:39 UTC
steppers
Joll503@A...
2002-07-11 01:32:19 UTC
Re: [CAD_CAM_EDM_DRO] steppers
jmkasunich
2002-07-11 07:34:41 UTC
Re: steppers
mariss92705
2002-07-11 09:24:54 UTC
Re: steppers
jmkasunich
2002-07-11 09:32:32 UTC
Re: steppers
Jon Elson
2002-07-11 10:04:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: steppers
Jon Elson
2002-07-11 10:06:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: steppers
Tony Jeffree
2002-07-11 11:39:29 UTC
Re: steppers
Gene
2002-07-25 20:09:50 UTC
steppers
JanRwl@A...
2002-07-25 20:18:49 UTC
Re: [CAD_CAM_EDM_DRO] steppers
Gene
2002-07-25 20:21:18 UTC
Re: [CAD_CAM_EDM_DRO] steppers
Jon Elson
2002-07-25 21:13:09 UTC
Re: [CAD_CAM_EDM_DRO] steppers
kilroy2k1
2002-07-26 14:51:10 UTC
Re: steppers
Bailey, Paul R
2002-07-26 22:39:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: steppers
Gene
2003-02-14 13:23:42 UTC
steppers