Re: stepless in New Jersey

Thanks Dan,

I had a problem with a virus a week or so ago and didn't get MAster5
back up yet. it got Master5 and Freecell. man I hated losing those
two programs.

and 9 and 10, step is on 9 oand +5V is on 10, (direction is on 9) of
the Gecko's (typo)

--- In CAD_CAM_EDM_DRO@y..., "Dan Statman" <dan.statman@r...> wrote:
> Dave,
>
> I initially had trouble because my parallel port was not the
default one
> addressed by turboCNC. Go into your setup screen and toggle to
another port
> address for the printer. I think there are 3 choices. One of them
should
> work for you.
>
> Dan.
>
> ----- Original Message -----
> From: "turbulatordude" <davemucha@j...>
> To: <CAD_CAM_EDM_DRO@y...>
> Sent: Friday, August 09, 2002 1:24 PM
> Subject: [CAD_CAM_EDM_DRO] stepless in New Jersey
>
>
> > Hi all,
> >
> > I need a little break.
> >
> > put together a simple power supply, 10 A transformer, has multiple
> > leads so I could get the voltage I like, 28 in this case. Outputs
> > just shy of 40 volts after a 68,000 uF cap.
> >
> > Old compac 486-100 and turboCNC
> >
> > I am trying to make sure everything is working properly.
> >
> > Gecko 201a ( early model) and a 0.85 amp 6 volt Vexta. uni-polar
> > connected as a bi-polar.
> >
> > The low voltage is just because I want to make sure it works.
> >
> > 470 alum cap on the 1 & 2 pins of the Gecko, 12K resistor on the
set-
> > resistor input. ( 1.5 A )
> >
> > TurboCNC set for port # 2 for step. # 3 for direction.
> >
> > Tried to output steps, but alas, no response. I did check the
set-up
> > and it was using port #2 for step, #3 for direction
> >
> > I am using the 5 volt from the computer power supply for the
> > step/direction power. could measure 5 v across the Gecko pins.
( 8
> > and 10)
> >
> > when I pulled the wire on step, I noticed the Gecko LED flicker a
> > little. by rubbing the lead onto the terminal ( I know, bad
idea) I
> > could see and hear the motor step.
> >
> > OK, oh wise ones, what am I doing wrong ? er... how best to get
> > this puppy to respond to software ?
> >
> > Dave
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it if
> you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
as a
> sister site to the CCED group, as many of the same members are
there, for OT
> subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> >
> > Post messages: CAD_CAM_EDM_DRO@y...
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >
> >