Re: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
Posted by
Jon Elson
on 2002-09-26 11:09:35 UTC
bjammin@... wrote:
(stepped-down shank) drills. Running a 1" drill in stainless with
a 1/2" shank in a 1/2" imported copy of a Jacobs chuck will be a very
frustrating exercise! I managed to get a good set of Morse taper
drills, and they are WONDERFUL to use!
Jon
> At 11:43 PM 9/25/02 -0500, you wrote:Right. But the original message was about using Silver&Deming
> > A Jacobs-
> >type chuck is just not strong enough for the larger drills.
>
> Tell it to Jacobs ... I have one in basement that runs from 3/32 all the
> way up to an inch, and it looks beefy enough for the job too.
(stepped-down shank) drills. Running a 1" drill in stainless with
a 1/2" shank in a 1/2" imported copy of a Jacobs chuck will be a very
frustrating exercise! I managed to get a good set of Morse taper
drills, and they are WONDERFUL to use!
Jon
Discussion Thread
deanc500
2002-09-25 06:31:57 UTC
What do you think of this mill?
deanc500
2002-09-25 06:34:28 UTC
What do you think of this mill?
doug98105
2002-09-25 07:45:07 UTC
Re: What do you think of this mill?
High Tech
2002-09-25 07:46:17 UTC
RE: [CAD_CAM_EDM_DRO] What do you think of this mill?
Mark
2002-09-25 08:17:04 UTC
Re: What do you think of this mill?
High Tech
2002-09-25 10:45:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
High Tech
2002-09-25 10:53:11 UTC
RE: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
Alan Marconett KM6VV
2002-09-25 11:20:37 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?
crisenbery99708
2002-09-25 13:39:40 UTC
Re: What do you think of this mill?
JJ
2002-09-25 16:40:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
Brian Punkar
2002-09-25 17:48:02 UTC
Re: What do you think of this mill?
Jon Elson
2002-09-25 21:34:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
bjammin@i...
2002-09-26 03:49:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
William Scalione
2002-09-26 11:06:19 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?
Jon Elson
2002-09-26 11:09:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: What do you think of this mill?
Alan Marconett KM6VV
2002-09-26 11:39:49 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?
William Scalione
2002-09-26 12:06:33 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?
jim davies
2002-09-26 16:03:44 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?
Raymond Heckert
2002-09-26 16:53:55 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?
Jerry Kimberlin
2002-09-26 16:56:42 UTC
Re: [CAD_CAM_EDM_DRO] What do you think of this mill?