CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup?CODE SAMPLE INCLUDED

Posted by Jim Brown
on 2002-11-01 22:14:30 UTC
Tim,
Thanks. Ill try that.

Regards,
Jim
Tim Goldstein <timg@...> wrote:When I view it in Discriminator or back plot it in Vector I see a cut at
depth being shown right at and after the G49 Z0 M5.

That is a cancel of a tool length offset and it is followed a couple of
lines down with a G43 tool length offset. My tempation would be to strip
out all the G41, G42, G43, and G49 and just run the tool paths from tool
centerline and see what happens. You have enough to deal with already
without needing to learn all about offsets and how they are implemented
on each controller.

Tim
[Denver, CO]

> -----Original Message-----

>
> Yeah, somehow the accel rate got misconfigured and I had to redo
> motor tuning. Deceleration on the Y axis was a little lower than the
> X and Y couldnt keep up.Hence the odd rapid Z safe move to the
> second set of pocketed arcs.
> But I still have a problem where it plunges into the
> material.... This is about half of the code attached, and
> approximately where it
> plunges diagnally into the stock. It's FANUC. MACH1 seems to
> like it (or then again, maybe thats the problem, as Surfcam
> FREE only comes
> with a few PP)
> The feed rate is slowed way down so I could pinpoint(somewhat) where
> the problem occurs.
> I've initially rewound the code in MACH1 and zero'd all axiis, then
> I jog to X0 Y0 Z1 and start the code from there. The code will run
> correctly throughout, with exception to where it crashes at the end
> of the portion of code that Ive included.If I let it run from this
> crash point,all the rest of the toolpaths are executed as they
> should be, but the "real time display" in MACH1 clearly shows the
> tool travel to X0 Y0 Z0 diagnally through the stock ,and then back
> up to safe Z(1), then it executes right from there.


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/




---------------------------------
Do you Yahoo!?
Y! Web Hosting - Let the expert host your web site

[Non-text portions of this message have been removed]

Discussion Thread

jagco1998 2002-11-01 11:31:25 UTC toolpath creation problem or wrong interpretor setup? Tim Goldstein 2002-11-01 12:00:07 UTC Re: [CAD_CAM_EDM_DRO] toolpath creation problem or wrong interpretor setup? jagco1998 2002-11-01 12:48:14 UTC Re: toolpath creation problem or wrong interpretor setup? j.guenther 2002-11-01 13:03:44 UTC RE: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup? Tim Goldstein 2002-11-01 13:08:29 UTC Re: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup? jagco1998 2002-11-01 20:07:19 UTC Re: toolpath creation problem or wrong interpretor setup?CODE SAMPLE INCLUDED Tim Goldstein 2002-11-01 21:32:18 UTC RE: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup?CODE SAMPLE INCLUDED Jim Brown 2002-11-01 22:14:30 UTC RE: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup?CODE SAMPLE INCLUDED Alan Marconett KM6VV 2002-11-02 10:29:45 UTC Re: toolpath creation problem or wrong interpretor setup? Jim Brown 2002-11-02 13:10:46 UTC Re: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup? Ian W. Wright 2002-11-03 07:15:21 UTC Re: [CAD_CAM_EDM_DRO] Re: toolpath creation problem or wrong interpretor setup? Alan Marconett KM6VV 2002-11-03 15:04:39 UTC Re: toolpath creation problem or wrong interpretor setup?