Re: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
Posted by
George Erhart
on 2002-12-03 04:51:22 UTC
Thanks to all who responded. I will probably go the sherline
motor mounts route. Currently, I have a sunk cost of $208.
That is for the xylotex controller and 3 PowerMax II stepper
motors. (I already have a 10A 24V power supply and a
2A 5V wall wart.) The sherline stepper mounts seem to run
~$160.00 + shipping. That will bring my hardware total to
~$370. That will leave just the software costs, plus additional
tooling. All of this will still be with in my goal of being less than
$500.
George
motor mounts route. Currently, I have a sunk cost of $208.
That is for the xylotex controller and 3 PowerMax II stepper
motors. (I already have a 10A 24V power supply and a
2A 5V wall wart.) The sherline stepper mounts seem to run
~$160.00 + shipping. That will bring my hardware total to
~$370. That will leave just the software costs, plus additional
tooling. All of this will still be with in my goal of being less than
$500.
George
----- Original Message -----
From: "Peter Homann" <peter.homann@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, December 03, 2002 1:17 AM
Subject: RE: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
> I would have to second Tim's assessment. I'm using one of the Sherline
> Stepper mounts on my conversion of a Taig Lathe (for the cross slide), and
> they are very well designed.
>
> I'm also using the Sherline left hand thread CNC mill leadscrew as well,
as
> it is the same thread and pitch as the Taig cross slide screw.
>
>
> Peter Homann
> mailto:Peter.Homann@...
> Adacel Technologies Limited,
> 250 Bay St, BRIGHTON, 3186, AUSTRALIA
> http://www.adacel.com <http://www.adacel.com>
> Telephone +61 (3) 8530 7777, Facsimile +61 (3) 9596 2960
> Mobile 0421-601 665
>
>
> -----Original Message-----
> From: Tim Goldstein [mailto:timg@...]
> Sent: Tuesday, 3 December 2002 4:17 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: RE: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
>
>
> > -----Original Message-----
> > The next step after this will be to build or buy some
> > motor mounts. My Z axis measures 0.016 backlash, the X&Y are
> > only ~0.002. I am thinking that I may need to get the
> > sherline Z axis CNC mount kit to get the new leadscrew and
> > bearings. For X&Y, I can either make my own or there are some
> > other pre-made options.
>
> I may be biased as I am a Sherline dealer, but the Sherline motor mounts
> are hard to beat. They use 2 ball bearings that are preloaded to handle
> the thrust on all 3 axes. They also include the zero backlash flexible
> couplers. I have used a third party motor mount for the first Sherline
> conversion I did and it used the stock washers for the thrust. While you
> may get the endplay low for now it will quickly grow. None of that
> problem with the Sherline kits.
>
> Tim
> [Denver CO]
> Sherline Products at Deep Discount
> Mach1 & DeskCNC with Credit Card ordering
> Contact me for discounts on DeskCNC & Sherline bundles
> www.KTMarketing.com/Sherline
Discussion Thread
kevinagilent
2002-12-02 17:15:54 UTC
xylotex controller anyone using it?
stevenson_engineers
2002-12-02 17:28:28 UTC
Re: xylotex controller anyone using it?
George Erhart
2002-12-02 18:34:42 UTC
Re: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
Peter Cruickshank
2002-12-02 20:44:55 UTC
Re: xylotex controller anyone using it?
Tim Goldstein
2002-12-02 21:16:38 UTC
RE: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
Peter Homann
2002-12-02 21:19:07 UTC
RE: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
Peter Homann
2002-12-02 22:18:37 UTC
RE: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
George Erhart
2002-12-03 04:51:22 UTC
Re: [CAD_CAM_EDM_DRO] xylotex controller anyone using it?
stevenson_engineers
2002-12-03 05:02:58 UTC
Re: xylotex controller anyone using it?
George Erhart
2002-12-03 12:25:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: xylotex controller anyone using it?
Marv Frankel
2002-12-03 12:53:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: xylotex controller anyone using it?
stevenson_engineers
2002-12-03 13:40:23 UTC
Re: xylotex controller anyone using it?
Tim Goldstein
2002-12-03 14:38:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: xylotex controller anyone using it?
George Erhart
2002-12-03 17:34:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: xylotex controller anyone using it?