CAD CAM EDM DRO - Yahoo Group Archive

Re: Software Question...

on 2002-12-15 19:34:01 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Robert Campbell" <bob@c...>
wrote:
> The cad and cam programs are independent of the type of drives
(stepper or
> servo). The Cam program in most cases puts out a G code (example
G01).
>
> The G code then is read by a control program like Mach1. In
today's PC world
> the control program will just put out step and direction signals.
At this
> point things change. If you look at the gecko drives
(www.geckodrive.com)
> they have different boxes for stepper or servo.
>
> I hope that this helps.
>
> Bob Campbell

Bob, I bought the G320's and I have looked about the Mach1 or
Master5 CNC. Not really sure of the difference....

Bill C.
>
>
> ----- Original Message -----
> From: <billsand@c...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Sunday, December 15, 2002 6:41 PM
> Subject: [CAD_CAM_EDM_DRO] Software Question...
>
>
> > I attempted this an hour or so ago and nothing happened - lets
see
> > what happens this time....
> >
> > Some software advertises that it is for stepper motors, some for
> > servo motors. Doesn't the driver match the motor and control
> > feedback from the encoder? I understand the open and closed loop
but
> > how far back into the system does it go - into the software? I
have
> > the mill sorted out (and on the way), the servomotors and
drivers on
> > the way but the software baffeles me with choices. I have some
time
> > to sort it out but some of you have been through this and I'm
sure
> > can offer educated suggestions!
> >
> > Thanks up front,
> >
> > Bill C.
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it if
> you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
to be a
> sister site to the CCED group, as many of the same members are
there, for OT
> subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >

Discussion Thread

gadget_c <billsand@c... 2002-12-15 19:02:49 UTC Software Question... natchamp_87 <mark@h... 2002-12-15 19:13:29 UTC Re: Software Question... Robert Campbell 2002-12-15 19:13:46 UTC Re: [CAD_CAM_EDM_DRO] Software Question... gadget_c <billsand@c... 2002-12-15 19:30:13 UTC Re: Software Question... gadget_c <billsand@c... 2002-12-15 19:34:01 UTC Re: Software Question... gadget_c <billsand@c... 2002-12-15 19:40:09 UTC Re: Software Question... jeffalanp <xylotex@h... 2002-12-15 20:02:39 UTC Re: Software Question... Ray Henry 2002-12-16 06:36:31 UTC Re: Re: Software Question...