Re: Highly accurate home switch was Re: 3D Contouring - Loss of Accuracy
Posted by
echnidna <echnidna@y...
on 2002-12-17 15:37:51 UTC
A highly accurate home switch could be made by using an optical switch mounted on the motor shaft in conjunction with a microswitch on the axis limit. The microswitch being used to enable the optical switch.
Regards
Bob Thomas
Regards
Bob Thomas
--- In CAD_CAM_EDM_DRO@yahoogroups.com, CL <datac@l...> wrote:
> Lee Studley wrote:
>
> >Hi Peter,
> >I've wondered if somehow a software provision/mechanism for
> >periodically re-home-ing during long duration programs could be
> >done. This is sort of a bandaid fix, but would reset the
> >accumulating error. Also, I've been (just) thinking of how one might
> >make a super accurate home position switch.
> >Just ideas,
> >-Lee
> >
> >
> I'm going to look over this thread when I get a little time later this
> evening.... But in regards the above, a little known Beta version From
> Flashcut included this long ago. It was 1.50, and was really a beta
> version around the time of 1.4. It allowed for the installation of a G27
> (?? been a while) anywhere in the file. It would force the machine to
> lift the Z axis to machine zero, then run to X-Y zero. Then, the typical
> homing routine would run, reset all machine 0 positions, then return to
> the job where it left off. It was fabulous, but was not really presented
> to the public for version 1. I have not had the need to use it since I
> had been running so stable, but it is a super cool technique....
>
> I forgot to try it out until just now, but as far as I know, this
> really great feature is ready to rock and roll in the new Version 2 of
> Flashcut. I'll be sure to double check tonight. if for some reason it is
> not in there, I'll be on the horn asking why !
>
> Chris L
Discussion Thread
Peter
2002-12-17 11:10:38 UTC
3D Contouring - Loss of Accuracy
Egroupscdh (E-mail)
2002-12-17 12:52:45 UTC
RE: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy
Peter
2002-12-17 13:18:43 UTC
Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy
jeffalanp <xylotex@h...
2002-12-17 14:02:50 UTC
Re: 3D Contouring - Loss of Accuracy
Lee Studley <indigo_red@q...
2002-12-17 14:42:37 UTC
Re: 3D Contouring - Loss of Accuracy
CL
2002-12-17 15:13:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
echnidna <echnidna@y...
2002-12-17 15:37:51 UTC
Re: Highly accurate home switch was Re: 3D Contouring - Loss of Accuracy
Peter
2002-12-17 15:57:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
IMService
2002-12-17 16:05:30 UTC
Re: 3D Contouring - Loss of Accuracy
volitan712003 <volitan@o...
2002-12-17 17:30:11 UTC
Re: 3D Contouring - Loss of Accuracy
Jon Elson
2002-12-17 18:25:30 UTC
Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy
Jon Elson
2002-12-17 18:38:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Jon Elson
2002-12-17 18:40:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Peter
2002-12-17 18:50:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Alan Marconett KM6VV
2002-12-17 19:10:56 UTC
Re: 3D Contouring - Loss of Accuracy
Ray Henry
2002-12-17 20:21:46 UTC
Re: 3D Contouring - Loss of Accuracy
Chris L
2002-12-17 21:22:24 UTC
Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy
RichD
2002-12-17 21:32:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Chris L
2002-12-17 21:32:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Hoyt McKagen
2002-12-18 06:12:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Fred Smith <imserv@v...
2002-12-18 09:30:31 UTC
Re: 3D Contouring - Loss of Accuracy
Jens Swales <jipeess2000@y...
2002-12-20 14:12:32 UTC
Re: 3D Contouring - Loss of Accuracy
CL
2002-12-20 15:09:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Egroupscdh (E-mail)
2002-12-20 15:21:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Chris L
2002-12-20 20:42:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Doug Fortune
2002-12-21 11:21:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy
Larry Van Duyn
2003-02-25 13:34:17 UTC
Vector
j.guenther
2003-02-25 13:37:06 UTC
RE: [CAD_CAM_EDM_DRO] Vector
Larry Van Duyn
2003-02-25 13:38:46 UTC
Vector