CAD CAM EDM DRO - Yahoo Group Archive

Re: 3D Contouring - Loss of Accuracy

Posted by IMService
on 2002-12-17 16:05:30 UTC
> Date: Tue, 17 Dec 2002 14:12:16 -0500
> From: Peter <prenolds@...>
>Subject: 3D Contouring - Loss of Accuracy
>I'm stumped! On my BP-clone knee mill, I've tried everything I can
>think of and nothing seems to produce the results I'm looking for. What
>I find is that running a large 3D file I gradually accumulate a small
>error typically in one of the most active axes which often exceeds 0.3mm
>or .012" after half an hour to an hour of running time. It is usually
>in the same direction, but not always. Below are some of the things

Look for a mechanical slippage. Possibly a loose set screw on a motor shaft or coupling.

Best Regards, Fred Smith- IMService

Listserve Special discounts and offers are at:
http://www.imsrv.com/grp.html

Discussion Thread

Peter 2002-12-17 11:10:38 UTC 3D Contouring - Loss of Accuracy Egroupscdh (E-mail) 2002-12-17 12:52:45 UTC RE: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy Peter 2002-12-17 13:18:43 UTC Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy jeffalanp <xylotex@h... 2002-12-17 14:02:50 UTC Re: 3D Contouring - Loss of Accuracy Lee Studley <indigo_red@q... 2002-12-17 14:42:37 UTC Re: 3D Contouring - Loss of Accuracy CL 2002-12-17 15:13:39 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy echnidna <echnidna@y... 2002-12-17 15:37:51 UTC Re: Highly accurate home switch was Re: 3D Contouring - Loss of Accuracy Peter 2002-12-17 15:57:27 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy IMService 2002-12-17 16:05:30 UTC Re: 3D Contouring - Loss of Accuracy volitan712003 <volitan@o... 2002-12-17 17:30:11 UTC Re: 3D Contouring - Loss of Accuracy Jon Elson 2002-12-17 18:25:30 UTC Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy Jon Elson 2002-12-17 18:38:51 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Jon Elson 2002-12-17 18:40:02 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Peter 2002-12-17 18:50:17 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Alan Marconett KM6VV 2002-12-17 19:10:56 UTC Re: 3D Contouring - Loss of Accuracy Ray Henry 2002-12-17 20:21:46 UTC Re: 3D Contouring - Loss of Accuracy Chris L 2002-12-17 21:22:24 UTC Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy RichD 2002-12-17 21:32:23 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Chris L 2002-12-17 21:32:52 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Hoyt McKagen 2002-12-18 06:12:38 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Fred Smith <imserv@v... 2002-12-18 09:30:31 UTC Re: 3D Contouring - Loss of Accuracy Jens Swales <jipeess2000@y... 2002-12-20 14:12:32 UTC Re: 3D Contouring - Loss of Accuracy CL 2002-12-20 15:09:11 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Egroupscdh (E-mail) 2002-12-20 15:21:57 UTC RE: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Chris L 2002-12-20 20:42:35 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Doug Fortune 2002-12-21 11:21:56 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Larry Van Duyn 2003-02-25 13:34:17 UTC Vector j.guenther 2003-02-25 13:37:06 UTC RE: [CAD_CAM_EDM_DRO] Vector Larry Van Duyn 2003-02-25 13:38:46 UTC Vector