CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy

on 2002-12-20 15:21:57 UTC
> From: CL [mailto:datac@...]
>
> ....
> It sure is nice to have, even if you just put in a G27 - M30 sequence at
> the end of EVERY job for a "fresh" start.
>
> Chris L

Doesn't sound like a good idea to me if this 'covers up' lost steps
somewhere and doesn't notify you.

I realize it's a pain but, unless you know the source of the lost steps, how
can you have confidence in your machine and/or control system?

Sounds like when my wife did the balancing of the checkbook - if it's within
$5-$10 it's ok - not! (I now balance the checkbook <vbg>)

Cheers,

Chuck Hackett
"Good judgment comes from experience, experience comes from bad judgment"
7.5" gauge Union Pacific Northern (4-8-4) 844
Railroad: Camp Creek Railroaders, Waverly, Nebraska, USA (3000', 7.5")
Home: Elkhorn, Nebraska (just west of Omaha)

Discussion Thread

Peter 2002-12-17 11:10:38 UTC 3D Contouring - Loss of Accuracy Egroupscdh (E-mail) 2002-12-17 12:52:45 UTC RE: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy Peter 2002-12-17 13:18:43 UTC Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy jeffalanp <xylotex@h... 2002-12-17 14:02:50 UTC Re: 3D Contouring - Loss of Accuracy Lee Studley <indigo_red@q... 2002-12-17 14:42:37 UTC Re: 3D Contouring - Loss of Accuracy CL 2002-12-17 15:13:39 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy echnidna <echnidna@y... 2002-12-17 15:37:51 UTC Re: Highly accurate home switch was Re: 3D Contouring - Loss of Accuracy Peter 2002-12-17 15:57:27 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy IMService 2002-12-17 16:05:30 UTC Re: 3D Contouring - Loss of Accuracy volitan712003 <volitan@o... 2002-12-17 17:30:11 UTC Re: 3D Contouring - Loss of Accuracy Jon Elson 2002-12-17 18:25:30 UTC Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy Jon Elson 2002-12-17 18:38:51 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Jon Elson 2002-12-17 18:40:02 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Peter 2002-12-17 18:50:17 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Alan Marconett KM6VV 2002-12-17 19:10:56 UTC Re: 3D Contouring - Loss of Accuracy Ray Henry 2002-12-17 20:21:46 UTC Re: 3D Contouring - Loss of Accuracy Chris L 2002-12-17 21:22:24 UTC Re: [CAD_CAM_EDM_DRO] 3D Contouring - Loss of Accuracy RichD 2002-12-17 21:32:23 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Chris L 2002-12-17 21:32:52 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Hoyt McKagen 2002-12-18 06:12:38 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Fred Smith <imserv@v... 2002-12-18 09:30:31 UTC Re: 3D Contouring - Loss of Accuracy Jens Swales <jipeess2000@y... 2002-12-20 14:12:32 UTC Re: 3D Contouring - Loss of Accuracy CL 2002-12-20 15:09:11 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Egroupscdh (E-mail) 2002-12-20 15:21:57 UTC RE: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Chris L 2002-12-20 20:42:35 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Doug Fortune 2002-12-21 11:21:56 UTC Re: [CAD_CAM_EDM_DRO] Re: 3D Contouring - Loss of Accuracy Larry Van Duyn 2003-02-25 13:34:17 UTC Vector j.guenther 2003-02-25 13:37:06 UTC RE: [CAD_CAM_EDM_DRO] Vector Larry Van Duyn 2003-02-25 13:38:46 UTC Vector