CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes

Posted by George Erhart
on 2003-01-13 18:22:20 UTC
What about using a worm gear reducer?

George
----- Original Message -----
> (1) the motors aren't powerful enough, apparently, to raise the knee.
> They stall and eventually cause my geckos to fault. I'm pretty sure
> I have the "limit" set to Max on the geckos.
>
> (2) when lowering the knee, the motor turns and every now again
> there's a 'thump' from the mill, as if the knee is not lowering
> smoothly, but in little increments.

Discussion Thread

jbordens <jake@a... 2003-01-13 16:58:46 UTC Z-Axis Knee Woes Brian 2003-01-13 18:15:44 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes torsten98001 <torsten@g... 2003-01-13 18:19:21 UTC Re: Z-Axis Knee Woes George Erhart 2003-01-13 18:22:20 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes mjf462001 <mjf46@j... 2003-01-13 19:10:35 UTC Re: Z-Axis Knee Woes Mariss Freimanis <mariss92705@y... 2003-01-13 19:16:16 UTC Re: Z-Axis Knee Woes Vince Negrete 2003-01-13 19:24:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Z-Axis Knee Woes Bernard R <bwjarandall@c... 2003-01-13 19:47:23 UTC Re: Z-Axis Knee Woes Mariss Freimanis <mariss92705@y... 2003-01-13 20:23:54 UTC Re: Z-Axis Knee Woes Raymond Heckert 2003-01-13 20:35:47 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes Peter 2003-01-13 20:50:47 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes Jon Elson 2003-01-13 23:27:30 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes Vince Negrete 2003-01-14 00:48:10 UTC More Questions on Z-Axis Drive Marv Frankel 2003-01-14 03:06:10 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes Les Watts 2003-01-14 04:55:01 UTC Re: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes Jon Elson 2003-01-14 10:14:35 UTC Re: [CAD_CAM_EDM_DRO] More Questions on Z-Axis Drive Dan Mauch 2003-01-14 12:14:24 UTC RE: [CAD_CAM_EDM_DRO] Z-Axis Knee Woes Bernard R <bwjarandall@c... 2003-01-14 17:04:15 UTC Re: Z-Axis Knee Woes Bernard R <bwjarandall@c... 2003-01-14 18:19:00 UTC Re: Z-Axis Knee Woes Les Watts 2003-01-14 19:04:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Z-Axis Knee Woes