Re: 5 volts in Geckos G201?????
Posted by
turbulatordude <davemucha@j...
on 2003-01-18 15:19:50 UTC
Raul,
if you have an LED, just a simple LED, and a 250 to 500 ohm resistor,
check to see if you get a voltage drop when connected on the end of
your cable from the +5 to ground.
I'm not sure of the power draw for the Gecko isolators, but you would
need to multiply that by the total number of Geckos and then double
it for the step and direction on each.
Dave
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "ralaco <ralaco@y...>"
<ralaco@y...> wrote:
if you have an LED, just a simple LED, and a 250 to 500 ohm resistor,
check to see if you get a voltage drop when connected on the end of
your cable from the +5 to ground.
I'm not sure of the power draw for the Gecko isolators, but you would
need to multiply that by the total number of Geckos and then double
it for the step and direction on each.
Dave
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "ralaco <ralaco@y...>"
<ralaco@y...> wrote:
> Art:
>
> Geckos take the ground from step and direction pins
> Pin 25 go to limits and E-stop in Mach1
>
> Regards
> Raul Lara
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Art <fenerty@h...> wrote:
> > no ground? YOu need a pin 25 from the PC to the gecko as well.
> >
> > Art
> > www.artofcnc.ca
Discussion Thread
ralaco <ralaco@y...
2003-01-18 13:58:45 UTC
5 volts in Geckos G201?????
Tim Goldstein
2003-01-18 14:06:06 UTC
RE: [CAD_CAM_EDM_DRO] 5 volts in Geckos G201?????
Mariss Freimanis <mariss92705@y...
2003-01-18 14:25:05 UTC
Re: 5 volts in Geckos G201?????
ralaco <ralaco@y...
2003-01-18 14:40:54 UTC
Re: 5 volts in Geckos G201?????
ralaco <ralaco@y...
2003-01-18 14:47:15 UTC
Re: 5 volts in Geckos G201?????
Art
2003-01-18 14:57:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: 5 volts in Geckos G201?????
Russ Waters
2003-01-18 14:57:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: 5 volts in Geckos G201?????
Mariss Freimanis <mariss92705@y...
2003-01-18 15:09:38 UTC
Re: 5 volts in Geckos G201?????
Mariss Freimanis <mariss92705@y...
2003-01-18 15:11:59 UTC
Re: 5 volts in Geckos G201?????
ralaco <ralaco@y...
2003-01-18 15:12:48 UTC
Re: 5 volts in Geckos G201?????
turbulatordude <davemucha@j...
2003-01-18 15:19:50 UTC
Re: 5 volts in Geckos G201?????
ralaco <ralaco@y...
2003-01-18 15:20:39 UTC
Re: 5 volts in Geckos G201?????
Tim Goldstein
2003-01-18 15:31:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: 5 volts in Geckos G201?????
Alan Marconett KM6VV
2003-01-18 15:35:09 UTC
Re: [CAD_CAM_EDM_DRO] 5 volts in Geckos G201?????
ralaco <ralaco@y...
2003-01-18 17:25:36 UTC
Re: 5 volts in Geckos G201????? to MARISS
Mariss Freimanis <mariss92705@y...
2003-01-18 18:19:06 UTC
Re: 5 volts in Geckos G201????? to MARISS
ralaco <ralaco@y...
2003-01-18 19:11:35 UTC
Re: 5 volts in Geckos G201????? to MARISS
JanRwl@A...
2003-01-19 13:31:19 UTC
Re: [CAD_CAM_EDM_DRO] 5 volts in Geckos G201?????