Re: [CAD_CAM_EDM_DRO] Re: Plasma cnc

I haven't had much experience with servos but I would be suprised if you had
any trouble with side loads. I am sure the bearings would be designed to
cope with this.

Les

> les,
>
> Im converting my table to servos and was going to use 2 to 1 ratio timing
> pulley. Do you have to worry about putting side load directly to the

output

> shaft of the motor or did you use some kind of bearing to help support the
> shaft? How much tension would you guess it takes to keep the belt tight?
>
> -----Original Message-----
> From: Les Newell [mailto:les@...]
> Sent: Saturday, January 18, 2003 1:44 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] Re: Plasma cnc
>
>
> I used 30mm HTD toothed belt for my plasma. It stretched very slightly

over

> the first couple of months but seems to be pretty stable now. As close as

I

> can measure the error is within +/-0.5mm (20 thou) over the whole travel

of

> my 2.5m x 1.5m (8' x 5') machine. This is of course nowhere near as

accurate

> as ballscrews but plasma isn't exactly high precision anyway!
>
> the HTD belt appears to have very little give in it. If I push hard on the
> gantry I can just see a small amount of deflection before I overcome the
> steppers. I would have thought it would be good enough for light routing,
> especially if you use two belts to move the gantry, one either side.
>
> I would be a little wary of chain, especially with all that abrasive

plasma

> dust hanging about. If my experience with motorcyles is anything to go by,
> you would need to tension the chain on a regular basis. Also chain is
> probably more expensive than toothed belts. You could buy all the belts

and

> pulleys for less than the cost of one ball nut!
>
> Les
>
>
> > Yeah, the Hypertherm Powermax 1250 is top of the line
> > for CNC plasma operations. It allready has the remote
> > torch on/off terminal installed for the G-Code to run
> > the torch. But at $3500 I say ouch. I am also drawing
> > up plans for a combo plasma/router cnc machine and am
> > looking at drive options. The ball screws for an
> > 5'X10' table run in the thousands of dollars. I was
> > wondering if anyone here has ever seen,used,heard of
> > chain and sprockets instead of screws? My parents have
> > a picture framing shop and they use a CNC mat cutter.
> > I was looking at the gantry rails to see what kind of
> > drive system was there and it's all small chain and
> > sprockets. a littls smaller than a bicycle chain would
> > be. seems like if the chain was tight enough there
> > would be no backlash. Since I want to use dual drive
> > on the long axis, I am going to need 20 feet of ball
> > screws, this is way out of budget at this point.
> > --- "Jens Swales <jipeess2000@...>"
> > <jipeess2000@...> wrote:
> > > hi
> > >
> > > i was recomended a plasma-rig from hypertherm, they
> > > dont produce
> > > those nasty ignition-sparks that knocks out the
> > > system
> > >
> > >
> > > js
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES:
> > > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe:
> > > CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe:
> > > CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > > wanliker@...
> > > Moderator: jmelson@...
> > > timg@... [Moderator]
> > > URL to this group:
> > > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru
> > > Google.com to reach it if you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I
> > > consider this to be a sister site to the CCED group,
> > > as many of the same members are there, for OT
> > > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC
> > > DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT
> > > ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> > > http://docs.yahoo.com/info/terms/
> > >
> > >
> >
> > =====
> > Visit my personal web site:
> > http://www.geocities.com/timbercutter_2000
> > -
> > You can also email me at:
> > tyson@...
> >
> > __________________________________________________
> > Do you Yahoo!?
> > Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
> > http://mailplus.yahoo.com
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: jmelson@... timg@... [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it

if

> you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for

OT

> subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to

http://docs.yahoo.com/info/terms/

> >
> >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it

if

> you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for

OT

> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>
>
> ------ http://USFamily.Net/info - Unlimited Internet - From

$8.99/mo! ------

>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:

aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.

> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a

sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.

DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........

> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>