Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ?
Posted by
Hans Wedemeyer
on 2003-01-20 17:27:29 UTC
Alan,
Yes I understand, however the back end of the Gecko is not going to be accessible, no way to "get at" screws of nuts, that's why a right angle bracket will do the trick. Two screw from the out side of the case will be the
only way I can fasten the back end.
Hans W
Alan Marconett KM6VV wrote:
Yes I understand, however the back end of the Gecko is not going to be accessible, no way to "get at" screws of nuts, that's why a right angle bracket will do the trick. Two screw from the out side of the case will be the
only way I can fasten the back end.
Hans W
Alan Marconett KM6VV wrote:
> Hi Hans,
>
> I don't think you'll have to disassemble the cover, but you will have to
> remove the two terminal blocks. Just tuck the back edge of the Gecko
> under two screw heads, then put in the front screws.
Discussion Thread
Hans Wedemeyer
2003-01-20 08:03:49 UTC
Best way to mount Gecko modules ?
eferg2001 <eferg@a...
2003-01-20 08:33:13 UTC
Re: Best way to mount Gecko modules ?
Alan Marconett KM6VV
2003-01-20 14:04:00 UTC
Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ?
Hans Wedemeyer
2003-01-20 14:17:16 UTC
Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ?
Alan Marconett KM6VV
2003-01-20 15:25:49 UTC
Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ?
Hans Wedemeyer
2003-01-20 17:27:29 UTC
Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ?
turbulatordude <davemucha@j...
2003-01-20 17:58:01 UTC
Re: Best way to mount Gecko modules ?
Vince Negrete
2003-01-20 20:43:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
Tim Goldstein
2003-01-20 21:23:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
JanRwl@A...
2003-01-20 22:50:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
Vince Negrete
2003-01-21 02:07:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
Les Watts
2003-01-21 05:54:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
sparkness2001 <mark@c...
2003-01-21 07:19:28 UTC
Re: Best way to mount Gecko modules ?
Vince Negrete
2003-01-21 08:17:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
Les Watts
2003-01-21 09:15:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?
Vince Negrete
2003-01-21 09:56:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?