CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?

Posted by Vince Negrete
on 2003-01-21 09:56:42 UTC
> A grounding rod is often several thousand ohms resistance
> in dry soil. Fine for lightning strikes but no good for
> a floating neutral.
> I have used Copley 412 as my standard drop-in servo amp
> for several years. It costs about $300 in small quantities.

Ok, thats a better price... The Salesman (of course) recommended I get the
Brushless Panelmount to match the motors.
Its the "Accelus".

> When Mariss finishes up the G310 I may switch to that
> as my standard servo amp because it will be around
> half the cost.

Now I'm wondering if I should wait then? I should be a Month or two at most
away from finishing the stuff I have to do.

> These are full servo amps with torque or velocity control.
> They take a plus or minus 10v analog input signal and
> are used with a servo controller rather than a stepper
> control.
>
> For encoders I recommend U.S. digital E3.
> It is about $50. This can be converted from single
> ended to differential with a little $12 snap on thing
> they sell , or you can make your own easily with an
> integrated circuit that costs about a dollar.
> I'll help you off list when you
> are ready to install some.
>

Most Appreciated.

Vince

Discussion Thread

Hans Wedemeyer 2003-01-20 08:03:49 UTC Best way to mount Gecko modules ? eferg2001 <eferg@a... 2003-01-20 08:33:13 UTC Re: Best way to mount Gecko modules ? Alan Marconett KM6VV 2003-01-20 14:04:00 UTC Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ? Hans Wedemeyer 2003-01-20 14:17:16 UTC Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ? Alan Marconett KM6VV 2003-01-20 15:25:49 UTC Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ? Hans Wedemeyer 2003-01-20 17:27:29 UTC Re: [CAD_CAM_EDM_DRO] Best way to mount Gecko modules ? turbulatordude <davemucha@j... 2003-01-20 17:58:01 UTC Re: Best way to mount Gecko modules ? Vince Negrete 2003-01-20 20:43:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? Tim Goldstein 2003-01-20 21:23:57 UTC RE: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? JanRwl@A... 2003-01-20 22:50:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? Vince Negrete 2003-01-21 02:07:54 UTC RE: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? Les Watts 2003-01-21 05:54:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? sparkness2001 <mark@c... 2003-01-21 07:19:28 UTC Re: Best way to mount Gecko modules ? Vince Negrete 2003-01-21 08:17:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? Les Watts 2003-01-21 09:15:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ? Vince Negrete 2003-01-21 09:56:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Best way to mount Gecko modules ?