Re: [CAD_CAM_EDM_DRO] blown Gecko - shorted output ?
Posted by
Alan Marconett KM6VV
on 2003-02-26 11:05:10 UTC
Hi Dave,
First, If you're using a PC for the motor power supply, GET RID OF IT!
Not enough voltage, transformer less, and it's reguated. Now regulated
might not be too bad, but a liner supply is no more then a xfmr, bridge
and cap (OK, some fuzes, etc.). If you care enough to buy Geckos...
HTH
Alan KM6VV
"turbulatordude " wrote:
First, If you're using a PC for the motor power supply, GET RID OF IT!
Not enough voltage, transformer less, and it's reguated. Now regulated
might not be too bad, but a liner supply is no more then a xfmr, bridge
and cap (OK, some fuzes, etc.). If you care enough to buy Geckos...
HTH
Alan KM6VV
"turbulatordude " wrote:
>
> Hi all,
>
> I blew us a couple Gecko 201's over the last week. Yeah, I'm
> thinking of pre-purchasing some of the more bullet proof ones when
> available.
> <SNIP>
> Power supply is an old PC box and is grounded to the 110VAC. same
> wall outlet as the PC.
> <SNIP>
> PC is powered 110VAC, and I did have it in another wall outlet,
> didn't check if it was on the same phase or a different phase.
>
> HELP !!!
>
> Dave
Discussion Thread
turbulatordude <davemucha@j...
2003-02-26 09:18:24 UTC
blown Gecko - shorted output ?
Alan Marconett KM6VV
2003-02-26 11:05:10 UTC
Re: [CAD_CAM_EDM_DRO] blown Gecko - shorted output ?
Lee Studley <indigo_red@q...
2003-02-26 11:50:29 UTC
Re: blown Gecko - shorted output ?
turbulatordude <davemucha@j...
2003-02-26 12:26:08 UTC
Re: blown Gecko - shorted output ?
turbulatordude <davemucha@j...
2003-02-26 12:42:29 UTC
Re: blown Gecko - shorted output ?
Jeff Goldberg
2003-02-26 13:26:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
Tony Jeffree
2003-02-26 13:35:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
turbulatordude <davemucha@j...
2003-02-26 14:01:43 UTC
Re: blown Gecko - shorted output ?
John Craddock
2003-02-26 14:41:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
Jeff Goldberg
2003-02-26 15:03:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
Jeff Goldberg
2003-02-26 15:12:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Important new question - was blown Gecko - shorted output ?
wanliker@a...
2003-02-26 16:19:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
Michael
2003-02-26 17:05:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
turbulatordude <davemucha@j...
2003-02-26 18:22:10 UTC
Re: blown Gecko - shorted output ?
Lee Studley <indigo_red@q...
2003-02-26 19:15:07 UTC
Re: blown Gecko - shorted output ?
turbulatordude <davemucha@j...
2003-02-26 20:49:49 UTC
Re: blown Gecko - shorted output ?
Raymond Heckert
2003-02-26 21:16:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
Raymond Heckert
2003-02-26 21:16:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
wanliker@a...
2003-02-26 21:25:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
turbulatordude <davemucha@j...
2003-02-26 21:55:38 UTC
Re: blown Gecko - shorted output ?
resosys
2003-03-26 14:11:00 UTC
Re: blown Gecko - shorted output ?
James Cullins
2003-03-26 16:35:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: blown Gecko - shorted output ?
turbulatordude
2003-03-26 20:03:32 UTC
Re: blown Gecko - shorted output ?