High or Low voltage steppers better for Gecko
Posted by
Dale Peterson
on 2003-05-13 17:05:32 UTC
Does anyone have a suggestion as to which of the steppers below would
work better for a Sherline 2000 retrofit?
I am planning on using Gecko 201 drives but have not ordered them yet so
I could be convinced to change to a different Gecko drive.
I will custom built the supply that I need when I decide on the motors
and drivers.
This one is 1 volt, 4 amp/phase
http://www.clickautomation.com/products/index.php?func=show&pid=401&cid=158
This one is 7.2 volt, 1 amp/phase
http://www.clickautomation.com/products/index.php?func=show&pid=399&cid=158
Has anyone had any problem dealing with .clickautomation.com?
Dale
work better for a Sherline 2000 retrofit?
I am planning on using Gecko 201 drives but have not ordered them yet so
I could be convinced to change to a different Gecko drive.
I will custom built the supply that I need when I decide on the motors
and drivers.
This one is 1 volt, 4 amp/phase
http://www.clickautomation.com/products/index.php?func=show&pid=401&cid=158
This one is 7.2 volt, 1 amp/phase
http://www.clickautomation.com/products/index.php?func=show&pid=399&cid=158
Has anyone had any problem dealing with .clickautomation.com?
Dale
Discussion Thread
onecooltoolfool
2003-03-30 10:10:29 UTC
Sherline Tool Changer - Sneak Peek
Jon Anderson
2003-03-30 11:08:16 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Tool Changer - Sneak Peek
Tim Goldstein
2003-03-30 11:23:45 UTC
RE: [CAD_CAM_EDM_DRO] Sherline Tool Changer - Sneak Peek
glee@i...
2003-03-30 13:24:26 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Tool Changer - Sneak Peek
Peter Cruickshank
2003-03-31 03:00:31 UTC
Re: Sherline Tool Changer - Sneak Peek
dcdziner
2003-03-31 03:33:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Sherline Tool Changer - Sneak Peek
Chris Baugher
2003-03-31 20:35:11 UTC
Servo motor voltage
Mariss Freimanis
2003-03-31 20:44:22 UTC
Re: Servo motor voltage
Chris Baugher
2003-03-31 21:34:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo motor voltage
Mariss Freimanis
2003-03-31 21:51:31 UTC
Re: Servo motor voltage
Chris Baugher
2003-03-31 22:26:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo motor voltage
Jon Elson
2003-03-31 22:55:33 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor voltage
Jon Elson
2003-03-31 22:59:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo motor voltage
Parker, Darcy
2003-04-01 04:53:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo motor voltage
bru103
2003-04-01 18:50:55 UTC
Re: Servo motor voltage
Parker, Darcy
2003-04-02 13:54:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo motor voltage
Mariss Freimanis
2003-04-02 15:03:32 UTC
Re: Servo motor voltage
Parker, Darcy
2003-04-03 05:13:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo motor voltage
Dale Peterson
2003-05-13 17:05:32 UTC
High or Low voltage steppers better for Gecko
turbulatordude
2003-05-13 17:20:20 UTC
Re: High or Low voltage steppers better for Gecko
Alan Marconett KM6VV
2003-05-13 17:44:46 UTC
Re: [CAD_CAM_EDM_DRO] High or Low voltage steppers better for Gecko
colin_jet
2003-05-13 17:51:41 UTC
Re: High or Low voltage steppers better for Gecko
JanRwl@A...
2003-05-13 20:50:27 UTC
Re: [CAD_CAM_EDM_DRO] High or Low voltage steppers better for Gecko
JanRwl@A...
2003-05-13 21:05:26 UTC
Re: [CAD_CAM_EDM_DRO] High or Low voltage steppers better for Gecko
mayfieldtm
2003-05-14 07:40:08 UTC
Re: High or Low voltage steppers better for Gecko
Andrew Werby
2003-05-14 12:45:40 UTC
Re: High or Low voltage steppers better for Gecko
mayfieldtm
2003-05-14 15:16:39 UTC
Re: High or Low voltage steppers better for Gecko