Re: [CAD_CAM_EDM_DRO] RE: DRO ENCODER TOOL

Thanks James,

I knew about US Digital. I was hoping this was something
else, as I was looking for a little higher resolution
linear encoders. (cheap)

Thanks

Mike




james owens wrote:

>
> From: "james owens" <wotisname@...>
>
> Hi Mike,
>
> The place to buy linear strip and encoders is usdigital.com they also do rotary encoders which are necessary should you wish to go over 360 in quarture.
>
> Regards,
>
> Terry.
> ----- Original Message -----
> From: Mike Gann
> To: CAD_CAM_EDM_DRO@onelist.com
> Sent: Thursday, March 09, 2000 7:04 PM
> Subject: Re: [CAD_CAM_EDM_DRO] RE: DRO ENCODER TOOL
>
> From: Mike Gann <mikegann@...>
>
> Tom -
>
> What was the resolution of your linear encoders and where
> did you buy them?
>
> thanks
>
> Mike
>
> "SMITH, THOMAS B. (JSC-DX)" wrote:
> >
> > From: "SMITH, THOMAS B. (JSC-DX)" <tbsmith@...>
> >
> > Terry,
> >
> > The pictures are very useful, thanks! And don't think you are beating this
> > to death. All this discussion has saved me (and others, I'm sure) a fair
> > amount of cash. I just finished installing DRO on my mill using linear
> > encoders for $150.00. Now with the tips from you, Art
> > and others, I can do the same for my lathe for a tenth that cost.
> >
> > One more question...did you remove the retaining clip before using your
> > tool?
> >
> > Tom
> >
> > >>>>>>>>>>>>
> > Message: 10
> > Date: Thu, 09 Mar 2000 00:26:49 -0000
> > From: "Terry May" <tmay@...>
> > Subject: DRO ENCODER TOOL
> >
> > At the risk of beating this subject to death, I made the wedge tools
> > I discussed earlier to remove the encoder disc from the Goldmine
> > electronics servo motors. The tool worked very well removing the
> > encoder and not damaging the disc.
> >
> > I put a couple of pictures of the wedges and the usage into the RCM
> > dropbox today (DRO_Tool.jpg, etc.) since I don't have my own web
> > site. Hope they are useful to someone.
> > Terry May
> > <<<<<<<<<<<<<<
> >
> > ------------------------------------------------------------------------
> > GET A NEXTCARD VISA, in 30 seconds! Get rates as low as 2.9%
> > Intro or 9.9% Fixed APR and no hidden fees. Apply NOW!
> > http://click.egroups.com/1/936/1/_/423600/_/952623637/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems in the above catagories.
> > To Unsubscribe, read archives, change to or from digest.
> > Go to: http://www.onelist.com/isregistered.cgi
> > Log on, and you will go to Member Center, and you can make changes there.
> > For the FAQ, go to http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
>
> ------------------------------------------------------------------------------
>
>
>
> ------------------------------------------------------------------------------
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes there.
> For the FAQ, go to http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
> [Non-text portions of this message have been removed]
>
> ------------------------------------------------------------------------
> DON'T HATE YOUR RATE!
> Get a NextCard Visa, in 30 seconds! Get rates as low as
> 0.0% Intro or 9.9% Fixed APR and no hidden fees.
> Apply NOW!
> http://click.egroups.com/1/2120/1/_/423600/_/952633090/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes there.
> For the FAQ, go to http://www.ktmarketing.com/faq.html
> bill,
> List Manager