CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] phase converter

Posted by R. Dean
on 2000-03-09 13:46:56 UTC
Joe, It is quite simple. Connect your 240VAC across two of the motor
windings. Connect the 3ph load circuit across those two windings and
the third leg. With the 3ph load switched off and the 240 1ph on, pull
the shaft cord to start (which ever direction suits you) then switch
on the 3ph load. Once you get that going we can tell you how to add a
dirt simple self start circuit. Much safer. Rich Dean


Joe Vicars wrote:
>
> From: Joe Vicars <jvicars@...>
>
> Can someone tell me exactly how to make a "pull start" phase
> converter from a 3 phase motor? I am going to try it this weekend and
> need some tips. I have a Baldor 3/4 3Ph that I want to drive a Rockwell
> belt sander with.
> Please dumb it down, I have zero electrical aptitude.
> Thanks.
>
> ------------------------------------------------------------------------
> MAXIMIZE YOUR CARD, MINIMIZE YOUR RATE!
> Get a NextCard Visa, in 30 seconds! Get rates as low as
> 0.0% Intro or 9.9% Fixed APR and no hidden fees.
> Apply NOW!
> http://click.egroups.com/1/2122/1/_/423600/_/952631994/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes there.
> For the FAQ, go to http://www.ktmarketing.com/faq.html
> bill,
> List Manager

--
/////
(o)-(o)
-----ooO---(_)---Ooo--------------------------
Rich Dean

Discussion Thread

R. Dean 2000-03-09 13:46:56 UTC Re: [CAD_CAM_EDM_DRO] phase converter Drew Rogge 2000-03-09 14:18:29 UTC Re: [CAD_CAM_EDM_DRO] phase converter paul@a... 2000-03-09 14:28:08 UTC Re: [CAD_CAM_EDM_DRO] phase converter Lngknife29@a... 2000-03-09 16:41:22 UTC Re: [CAD_CAM_EDM_DRO] phase converter Steve Carlisle 2000-03-09 17:35:33 UTC Re: [CAD_CAM_EDM_DRO] phase converter JanRwl@A... 2000-03-09 17:52:24 UTC Re: [CAD_CAM_EDM_DRO] phase converter JanRwl@A... 2000-03-09 17:57:28 UTC Re: [CAD_CAM_EDM_DRO] phase converter Tim Goldstein 2000-03-09 20:30:34 UTC RE: [CAD_CAM_EDM_DRO] phase converter R. Dean 2000-03-09 21:39:56 UTC Re: [CAD_CAM_EDM_DRO] phase converter David M. Munro 2000-03-10 05:56:30 UTC Re: [CAD_CAM_EDM_DRO] phase converter Jon Anderson 2000-03-10 06:25:16 UTC Re: [CAD_CAM_EDM_DRO] phase converter Charles VanLeeuwen 2000-03-10 07:44:38 UTC Re: [CAD_CAM_EDM_DRO] phase converter Carlos Guillermo 2000-03-10 08:13:13 UTC VFD / phase converter D.F.S. 2000-03-10 08:45:48 UTC Re: [CAD_CAM_EDM_DRO] Rotary Phase converter design?