Re: [CAD_CAM_EDM_DRO] phase converter
Posted by
paul@a...
on 2000-03-09 14:28:08 UTC
No, pick any two. If the 3 phase motor on your tool runs in reverse,
swap any two wires going to the motor.
------------\---------------------
\
220 3 ph ________________ 3 phase
motor to tool motor
/
-------------/--------------------
Paul Amaranth | Rochester MI, USA
Aurora Group, Inc. | Systems & Software
paul@... | Unix / Windows / NT
swap any two wires going to the motor.
------------\---------------------
\
220 3 ph ________________ 3 phase
motor to tool motor
/
-------------/--------------------
>--
> From: Drew Rogge <drew@...>
>
> Rich,
>
> I didn't ask the initial question but would like to thank you
> for the dirt simple answer. Does it matter which of the motor
> windings the 240 and 3 phase stuff is connected to?
>
> Drew
>
> On Mar 9, 4:45pm, R. Dean wrote:
> > Subject: Re: [CAD_CAM_EDM_DRO] phase converter
> > From: "R. Dean" <cmsteam@...>
> >
> > Joe, It is quite simple. Connect your 240VAC across two of the motor
> > windings. Connect the 3ph load circuit across those two windings and
> > the third leg. With the 3ph load switched off and the 240 1ph on, pull
> > the shaft cord to start (which ever direction suits you) then switch
> > on the 3ph load. Once you get that going we can tell you how to add a
> > dirt simple self start circuit. Much safer. Rich Dean
> >
> > /////
> > (o)-(o)
> > -----ooO---(_)---Ooo--------------------------
> > Rich Dean
> >
> >-- End of excerpt from R. Dean
>
>
>
> --
> Drew Rogge
> drew@...
>
> ------------------------------------------------------------------------
> GET A NEXTCARD VISA, in 30 seconds! Get rates
> as low as 0.0% Intro APR and no hidden fees.
> Apply NOW!
> http://click.egroups.com/1/975/1/_/423600/_/952640244/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes there.
> For the FAQ, go to http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
Paul Amaranth | Rochester MI, USA
Aurora Group, Inc. | Systems & Software
paul@... | Unix / Windows / NT
Discussion Thread
R. Dean
2000-03-09 13:46:56 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Drew Rogge
2000-03-09 14:18:29 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
paul@a...
2000-03-09 14:28:08 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Lngknife29@a...
2000-03-09 16:41:22 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Steve Carlisle
2000-03-09 17:35:33 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
JanRwl@A...
2000-03-09 17:52:24 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
JanRwl@A...
2000-03-09 17:57:28 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Tim Goldstein
2000-03-09 20:30:34 UTC
RE: [CAD_CAM_EDM_DRO] phase converter
R. Dean
2000-03-09 21:39:56 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
David M. Munro
2000-03-10 05:56:30 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Jon Anderson
2000-03-10 06:25:16 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Charles VanLeeuwen
2000-03-10 07:44:38 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Carlos Guillermo
2000-03-10 08:13:13 UTC
VFD / phase converter
D.F.S.
2000-03-10 08:45:48 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Phase converter design?