VFD / phase converter
Posted by
Carlos Guillermo
on 2000-03-10 08:13:13 UTC
Charles-
I hope you're right. I'm looking at buying one from KB Electronics for my
still-on-the-pallet Southbend lathe. The guys at KB recommended I use their
KBVF inverter to run the 1HP 3-phase motor with variable speed, reversing,
adj. ramped start up, etc. Lot's of goodies. It's not an industrially
"hardened" unit, but just mount it in a box, wire it to the motor and line,
and wire a potentiometer and a direction switch to it.
They sell it through distributors for $190.
web site
http://www.kbelectronics.com/
Data sheet
http://www.kbelectronics.com/catalog/gc115/kbvf.pdf
Carlos Guillermo
I hope you're right. I'm looking at buying one from KB Electronics for my
still-on-the-pallet Southbend lathe. The guys at KB recommended I use their
KBVF inverter to run the 1HP 3-phase motor with variable speed, reversing,
adj. ramped start up, etc. Lot's of goodies. It's not an industrially
"hardened" unit, but just mount it in a box, wire it to the motor and line,
and wire a potentiometer and a direction switch to it.
They sell it through distributors for $190.
web site
http://www.kbelectronics.com/
Data sheet
http://www.kbelectronics.com/catalog/gc115/kbvf.pdf
Carlos Guillermo
> -----Original Message-----
> From: Charles VanLeeuwen [mailto:cavlon@...]
> Sent: Friday, March 10, 2000 10:45 AM
> To: CAD_CAM_EDM_DRO@onelist.com
> Subject: Re: [CAD_CAM_EDM_DRO] phase converter
>
>
> From: "Charles VanLeeuwen" <cavlon@...>
>
> My personal experience with solid state variable frequency inverter drives
> used as phase converters is that they are less expensive, less noisy, and
> more efficient than at least some commercial rotary phase converters.
>
> CVL
Discussion Thread
R. Dean
2000-03-09 13:46:56 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Drew Rogge
2000-03-09 14:18:29 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
paul@a...
2000-03-09 14:28:08 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Lngknife29@a...
2000-03-09 16:41:22 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Steve Carlisle
2000-03-09 17:35:33 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
JanRwl@A...
2000-03-09 17:52:24 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
JanRwl@A...
2000-03-09 17:57:28 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Tim Goldstein
2000-03-09 20:30:34 UTC
RE: [CAD_CAM_EDM_DRO] phase converter
R. Dean
2000-03-09 21:39:56 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
David M. Munro
2000-03-10 05:56:30 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Jon Anderson
2000-03-10 06:25:16 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Charles VanLeeuwen
2000-03-10 07:44:38 UTC
Re: [CAD_CAM_EDM_DRO] phase converter
Carlos Guillermo
2000-03-10 08:13:13 UTC
VFD / phase converter
D.F.S.
2000-03-10 08:45:48 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Phase converter design?