Re: Ball screw cost and sources - Moglice - Phillycast - concrete

Hi Guys,

I may be catching the tail end of the conversatin here, but there
have been lots of talk about Moglice and using that to repair
leadscrews.

Moglice is also pretty good for adding a low friction layer between
components like a saddle when you have ground the years of misuse
away and want to get it back on center too.

I think that Philly Cast is for making the ways and supports and all.
and if you are going that far, there was at least one guy who used
concrete to pour the bed and I think he embedded the rails in that.

Dave



--- In CAD_CAM_EDM_DRO@yahoogroups.com, "dcdziner" <Dcdziner@p...>
wrote:

> Jan,
> I dug through my archives an came up with this .PDF file that

was sent

> to me by Les Watts. http://www.phillycast.com/products/inst-nut.pdf.
> Although it refers to Ball Nut Applications, Les indicated to me

that it

> would work for Acme screws as well. Since Les is the guru of this
> application, you might want to contact him for any further

information, at

> leswatts@a... . I hope this helps.
>
> Marv Frankel
> Los Angeles
>
> ----- Original Message -----
> From: <JanRwl@A...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Sunday, May 25, 2003 10:19 PM
> Subject: Re: [CAD_CAM_EDM_DRO] Ball screw cost and sources
>
>
> > In a message dated 5/25/2003 8:03:29 PM Central Standard Time,
> > Dcdziner@p... writes:
> >
> > > You didn't dig quite far enough into their web site. The

compound that

> > > they have is pumped into a worn nut
> >
> > I see! OK, I'll wait for it. Thanks. JRR
> >
> >
> > [Non-text portions of this message have been removed]
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,

wanliker@a...,

> timg@k...
> > Moderator: pentam@c... indigo_red@q... [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to

reach it if

> you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this

to be a

> sister site to the CCED group, as many of the same members are

there, for OT

> subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY

POSTING THEM.

> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to

http://docs.yahoo.com/info/terms/

> >