CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Is there a way to drill holes with a router?

on 2003-05-31 13:27:48 UTC
Raul,

I do a lot of drilling with my Porter Cable router, but I use router bits.

My procedure depending on the thickness is to use a router bit and spot
drill a shallow hole. I then take my part to a drill press and drill it to
size.

For thin material, I either drill a small hole typically with an 1/8 " bit
or use the bit to pocket out the correct hole size.

I don't think a drill bit would work.

Bob Campbell
----- Original Message -----
From: "ralaco" <ralaco@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, May 31, 2003 12:05 PM
Subject: [CAD_CAM_EDM_DRO] Is there a way to drill holes with a router?


> Can I use drill bits with a router? If so what speed I must use with
> a 3.25 Hp 5 Speed Porter Cable Router?
>
> I need to drill different hole sizes in a aluminum and acrylic plates
> and then, cutout some circles from the same plates.
>
> I'm asking this because the router speed is much more higher than a
> drill.
>
> Raul Lara
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>

Discussion Thread

ralaco 2003-05-31 12:05:39 UTC Is there a way to drill holes with a router? Robert Campbell 2003-05-31 13:27:48 UTC Re: [CAD_CAM_EDM_DRO] Is there a way to drill holes with a router? Carl Mikkelsen 2003-05-31 13:32:53 UTC Re: [CAD_CAM_EDM_DRO] Is there a way to drill holes with a router? ralaco 2003-05-31 14:31:31 UTC Re: Is there a way to drill holes with a router? Tim Goldstein 2003-05-31 15:10:03 UTC RE: [CAD_CAM_EDM_DRO] Re: Is there a way to drill holes with a router? turbulatordude 2003-05-31 15:11:21 UTC Re: Is there a way to drill holes with a router? Robert Campbell 2003-05-31 18:54:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Is there a way to drill holes with a router? wanliker@a... 2003-05-31 22:50:05 UTC Is there a way to drill holes with a router?