Re: servo motor shaft 5/8 to 1/4...best way??
Posted by
turbulatordude
on 2003-06-24 12:29:00 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "etauch" <erictauch@a...>
wrote:
if you remove 3/8 of the shaft OD, you are permantly lowering the
maximum torque of the motor.
Making an adapter is much easier. make a sleeve with both a 1/4 ID
and a 5/8 id. or get a 5/8 coupler and make a 1/4 to 5/8 bushing.
Dave
wrote:
> Hello,If you have a lathe make a coupler.
>
> I am considering some servo motors which have a 5/8 shaft, but I
> need to couple to 1/4 shaft couplers. I cannot open the couplers
> up enough, so I am trying to figure out the best way reduce the
> shaft diameter, or maybe attach a 1/4" adapter endpiece.
>
> My question: Can the shafts be easily removed from a servo motor
> to be chucked up in a lathe? Will I never get the thing
> re-assembled properly? Maybe even chuck the motor in the lathe
> and power it up!!??
>
> All suggestions appreciated.
>
> Thanks,
>
> Eric
if you remove 3/8 of the shaft OD, you are permantly lowering the
maximum torque of the motor.
Making an adapter is much easier. make a sleeve with both a 1/4 ID
and a 5/8 id. or get a 5/8 coupler and make a 1/4 to 5/8 bushing.
Dave
Discussion Thread
etauch
2003-06-24 11:34:28 UTC
servo motor shaft 5/8 to 1/4...best way??
Tim Goldstein
2003-06-24 11:38:48 UTC
RE: [CAD_CAM_EDM_DRO] servo motor shaft 5/8 to 1/4...best way??
Harvey White
2003-06-24 11:45:23 UTC
Re: [CAD_CAM_EDM_DRO] servo motor shaft 5/8 to 1/4...best way??
turbulatordude
2003-06-24 12:29:00 UTC
Re: servo motor shaft 5/8 to 1/4...best way??
Bernard R
2003-06-24 22:30:40 UTC
Re: servo motor shaft 5/8 to 1/4...best way??
Don Rogers
2003-06-24 22:53:16 UTC
Re: servo motor shaft 5/8 to 1/4...best way??
Torsten
2003-06-25 11:01:17 UTC
Re: servo motor shaft 5/8 to 1/4...best way??
dcdziner
2003-06-25 12:01:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo motor shaft 5/8 to 1/4...best way??
etauch
2003-06-25 15:05:45 UTC
Re: servo motor shaft 5/8 to 1/4...shaft butcher
dcdziner
2003-06-25 16:18:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo motor shaft 5/8 to 1/4...shaft butcher
etauch
2003-06-25 18:38:13 UTC
Re: servo motor shaft 5/8 to 1/4...shaft butcher
Jon Elson
2003-06-27 19:41:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo motor shaft 5/8 to 1/4...shaft butcher
Jon Elson
2003-06-27 19:41:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo motor shaft 5/8 to 1/4...shaft butcher
turbulatordude
2003-06-28 08:46:28 UTC
Re: servo motor shaft 5/8 to 1/4...shaft butcher