Re: I made it go! (Newb questions)
Posted by
ghidera2000
on 2003-07-06 15:16:59 UTC
Ok, so if I understand this right, it doesn't matter if I have the
coils in the "right" order, as long as I have them grouped properly?
e.g. (wish I could add a picture)
Wire 1
Tap 1&2 -- Three make one coil group
Wire 2
Wire 3
Tap 3&4 -- The other coil group
Wire 4
So if I have my wiring order actually like this:
Wire 2
Tap 1&2 -- Three make one coil group
Wire 1
Wire 3
Tap 3&4 -- The other coil group
Wire 4
Its still fine - it'll just go the opposite direction? If so, then
really all I have to do is swap one coil's wires and thats it?
Nothing else nasty happens? (No smoke yet, so I guess so :D )
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<davemucha@j...> wrote:
coils in the "right" order, as long as I have them grouped properly?
e.g. (wish I could add a picture)
Wire 1
Tap 1&2 -- Three make one coil group
Wire 2
Wire 3
Tap 3&4 -- The other coil group
Wire 4
So if I have my wiring order actually like this:
Wire 2
Tap 1&2 -- Three make one coil group
Wire 1
Wire 3
Tap 3&4 -- The other coil group
Wire 4
Its still fine - it'll just go the opposite direction? If so, then
really all I have to do is swap one coil's wires and thats it?
Nothing else nasty happens? (No smoke yet, so I guess so :D )
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<davemucha@j...> wrote:
> First off, CONGRATULATIONS ! and welcome to the club !got
>
> It is an awesome thing just to hear the motor move and to watch it
> take baby steps.
>
> Enjoy the moment and the fact that you are one in a million that
> that far!software
>
>
> regarding your wiring, if it spins in the direction you have no
> problems. if it spins in reverse from the way you expect, your
> choices are to change the output on the direction pin. most
> will let you chose HI or LOW to go clockwise you you don't have toswap 2
> move wires.
>
> but, it you want to change direction, all you need to do is to
> wires. leave one coil alone and just change one coil.
>
> very easy.
>
> Dave
Discussion Thread
ghidera2000
2003-07-06 13:39:55 UTC
I made it go! (Newb questions)
JanRwl@A...
2003-07-06 13:54:42 UTC
Re: [CAD_CAM_EDM_DRO] I made it go! (Newb questions)
turbulatordude
2003-07-06 14:48:14 UTC
Re: I made it go! (Newb questions)
ghidera2000
2003-07-06 15:16:59 UTC
Re: I made it go! (Newb questions)
JanRwl@A...
2003-07-06 19:12:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: I made it go! (Newb questions)
sam sokolik
2003-07-07 08:13:35 UTC
Re: [CAD_CAM_EDM_DRO] I made it go! (Newb questions)
ghidera2000
2003-07-07 08:18:19 UTC
Re: I made it go! (Newb questions)
sam sokolik
2003-07-07 21:51:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: I made it go! (Newb questions)
ghidera2000
2003-07-08 08:39:40 UTC
Re: I made it go! (Newb questions)