Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
Posted by
Jon Elson
on 2003-07-18 09:33:33 UTC
cnchomeman wrote:
which sounds wrong. there may be some current limiting inside the Gecko,
but if that is the same +5 V source for the encoder, it should have 100 + mA
of capacity, which certainly sounds bad. Mariss? Can you explain?
Jon
>>You have +5 V going through a relay contact and then to the base ofWell, it certainly shows a switch connecting 5 V to the transistor base,
>>
>>
>an
>
>
>>NPN transistor. You need to put a series resistor (say, 10 K Ohms)
>>
>>
>in
>
>
>>series with the wire to the base, or it will draw lots of current
>>
>>
>and
>
>
>>destroy the transistor (and possibly the drive, too).
>>
>>Jon
>>
>>
>
>You may be correct, but I stole this part of the circuit directly
>from the geckodrive manual, as can be seen on the geckodrive
>website. Here is an image of the curcuit. Is this a typo? Should I
>put the resistor in?
>
>http://www.e-zflight.com/files/ncnczj.jpg
>
>
which sounds wrong. there may be some current limiting inside the Gecko,
but if that is the same +5 V source for the encoder, it should have 100 + mA
of capacity, which certainly sounds bad. Mariss? Can you explain?
Jon
Discussion Thread
cnchomeman
2003-07-16 12:32:49 UTC
err/res circuit
cnchomeman
2003-07-16 12:44:39 UTC
Re: err/res circuit(updated picture)
caudlet
2003-07-16 16:36:00 UTC
Re: err/res circuit(updated picture)
cnchomeman
2003-07-16 17:23:36 UTC
Re: err/res circuit(updated picture)
Jon Elson
2003-07-17 09:53:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
Jon Elson
2003-07-17 10:11:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
Jon Elson
2003-07-17 10:12:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
cnchomeman
2003-07-17 17:33:56 UTC
Re: err/res circuit(updated picture)
Jon Elson
2003-07-18 09:33:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
cnchomeman
2003-07-18 09:39:11 UTC
Re: err/res circuit(updated picture)
caudlet
2003-07-18 15:06:17 UTC
Re: err/res circuit(updated picture)
James Cullins
2003-07-19 18:41:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
andyolney
2003-07-21 09:09:36 UTC
Re: err/res circuit(updated picture)
James Cullins
2003-07-21 11:11:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
James Cullins
2003-07-21 19:46:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: err/res circuit(updated picture)
cnchomeman
2003-07-23 21:44:26 UTC
Re: err/res circuit(updated picture)