Re: Router spindle electrical noise.
Posted by
cncman172
on 2003-10-20 09:27:16 UTC
Jon,
I had the very same problem and I resolved it by replacing the cable
on my limit and home switches with braid shielded cable. Make sure
you only ground the shield to the end that attaches to the controller
and leave it ungrounded at the switch or sensor end. As soon as I
made these changes all my limit and home switch problems vanished...
amazing...
Russ
I had the very same problem and I resolved it by replacing the cable
on my limit and home switches with braid shielded cable. Make sure
you only ground the shield to the end that attaches to the controller
and leave it ungrounded at the switch or sensor end. As soon as I
made these changes all my limit and home switch problems vanished...
amazing...
Russ
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
>
>
> balsaman_cnc wrote:
>
> >The electrical noise generated by my Porter cable Router is
> >triggering my limit switch circuit. The limits are high and go
low
> >if there is a problem. They are all in series (NC). If I set the
> >speed on my router down 20% or so the problem goes away. I slid
one
> >of those ferrite donuts over the limit switch cable with no
effect.
> >Is there something else I can try? I used shielded cable on all
> >cabling EXCEPT the limit switches...do I need to replace all that
> >cable? Are there other options?
> >
> >
> Probably putting a .01 uF capacitor from the input of the parallel
port
> and the ground connection of the parallel port should absorb some of
> the noise.
>
> Jon
Discussion Thread
balsaman_cnc
2003-10-19 09:26:33 UTC
Router spindle electrical noise.
Lee Studley
2003-10-19 13:32:37 UTC
Re: Router spindle electrical noise.
Dan
2003-10-19 17:03:56 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
John Johnson
2003-10-19 17:04:48 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
Jon Elson
2003-10-19 22:12:44 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
Superonline
2003-10-20 07:53:46 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
Carl Mikkelsen
2003-10-20 08:57:13 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
cncman172
2003-10-20 09:27:16 UTC
Re: Router spindle electrical noise.
cnc002@a...
2003-10-20 11:00:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Router spindle electrical noise.
c_holm10017
2003-10-20 14:26:47 UTC
RF Shielding - was Re: Router spindle electrical noise.
Paul
2003-10-20 15:22:02 UTC
Re: [CAD_CAM_EDM_DRO] RF Shielding - was Re: Router spindle electrical noise.
balsaman_cnc
2003-10-20 20:42:26 UTC
Re: Router spindle electrical noise.
jimalb2309
2003-10-20 20:42:47 UTC
RF Shielding - was Re: Router spindle electrical noise.
Chris Cowley
2003-10-21 07:40:25 UTC
Re: [CAD_CAM_EDM_DRO] RF Shielding - was Re: Router spindle electrical noise.
Dan Peirce
2003-10-21 07:41:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Router spindle electrical noise.
balsaman_cnc
2003-10-21 09:35:02 UTC
Re: Router spindle electrical noise.
balsaman_cnc
2003-10-22 08:16:28 UTC
Re: Router spindle electrical noise. SOLVED