Re: Router spindle electrical noise.
Posted by
Lee Studley
on 2003-10-19 13:32:37 UTC
Is your limit sensing loop AC or DC, you could place an capacitor
across the lines as the go back into the control to try to snub the
induced noise. Try a .22uF to start, the larger the value, the more
snubbing, but the response to limits time will be reduced.
Also try one of the AC line filters on the voltage going to the
router.
Describe your setup more withe repsect to what breakout or control you
are using.
-Lee
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "balsaman_cnc"
<balsaman_cnc@y...> wrote:
across the lines as the go back into the control to try to snub the
induced noise. Try a .22uF to start, the larger the value, the more
snubbing, but the response to limits time will be reduced.
Also try one of the AC line filters on the voltage going to the
router.
Describe your setup more withe repsect to what breakout or control you
are using.
-Lee
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "balsaman_cnc"
<balsaman_cnc@y...> wrote:
> The electrical noise generated by my Porter cable Router isone
> triggering my limit switch circuit. The limits are high and go low
> if there is a problem. They are all in series (NC). If I set the
> speed on my router down 20% or so the problem goes away. I slid
> of those ferrite donuts over the limit switch cable with noeffect.
> Is there something else I can try? I used shielded cable on all
> cabling EXCEPT the limit switches...do I need to replace all that
> cable? Are there other options?
>
> Thanks for any help you can provide.
>
> Eric
Discussion Thread
balsaman_cnc
2003-10-19 09:26:33 UTC
Router spindle electrical noise.
Lee Studley
2003-10-19 13:32:37 UTC
Re: Router spindle electrical noise.
Dan
2003-10-19 17:03:56 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
John Johnson
2003-10-19 17:04:48 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
Jon Elson
2003-10-19 22:12:44 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
Superonline
2003-10-20 07:53:46 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
Carl Mikkelsen
2003-10-20 08:57:13 UTC
Re: [CAD_CAM_EDM_DRO] Router spindle electrical noise.
cncman172
2003-10-20 09:27:16 UTC
Re: Router spindle electrical noise.
cnc002@a...
2003-10-20 11:00:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Router spindle electrical noise.
c_holm10017
2003-10-20 14:26:47 UTC
RF Shielding - was Re: Router spindle electrical noise.
Paul
2003-10-20 15:22:02 UTC
Re: [CAD_CAM_EDM_DRO] RF Shielding - was Re: Router spindle electrical noise.
balsaman_cnc
2003-10-20 20:42:26 UTC
Re: Router spindle electrical noise.
jimalb2309
2003-10-20 20:42:47 UTC
RF Shielding - was Re: Router spindle electrical noise.
Chris Cowley
2003-10-21 07:40:25 UTC
Re: [CAD_CAM_EDM_DRO] RF Shielding - was Re: Router spindle electrical noise.
Dan Peirce
2003-10-21 07:41:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Router spindle electrical noise.
balsaman_cnc
2003-10-21 09:35:02 UTC
Re: Router spindle electrical noise.
balsaman_cnc
2003-10-22 08:16:28 UTC
Re: Router spindle electrical noise. SOLVED