Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Posted by
Les Newell
on 2003-12-19 12:38:50 UTC
Hi John,
Ihave been running my mill and all the ways appear to be getting a good supply of oil :-)
I am a bit concerned about the quill bearings though. There does not appear to be any oil/grease being thrown out of the bearings so they could be short of lubricant. Should I expect to see a small amount of lubricant being thrown out or am I just paranoid?
Thanks,
Les
Ihave been running my mill and all the ways appear to be getting a good supply of oil :-)
I am a bit concerned about the quill bearings though. There does not appear to be any oil/grease being thrown out of the bearings so they could be short of lubricant. Should I expect to see a small amount of lubricant being thrown out or am I just paranoid?
Thanks,
Les
>These are little threaded brass fittings right at the oil port in the
>cast iron.
>So, follow the lines from the oil manifold to the ends. They should have
>a model code, a number from 0-3 usually, and an arrow to show flow
>direction. You should be able to remove them from the iron and reattach
>them to the tube and run the oil pump. Then you can see how much they
>deliver. The numbers are related to oil flow. Each number larger is
>twice the oil flow. Check www.bijur.com for more info.
>
>The orifices in the saddle are impossible to reach without removing the
>table. Ugh!
>
>
>
Discussion Thread
riaanbarnard2000
2003-12-04 12:41:11 UTC
Spindle controll
Les Newell
2003-12-06 05:18:43 UTC
Series 1 Bridegport CNC manuals?
vavaroutsos
2003-12-06 09:25:42 UTC
Re: Series 1 Bridegport CNC manuals?
jim davies
2003-12-06 10:44:41 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Steve
2003-12-06 11:06:26 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Jon Elson
2003-12-06 15:11:20 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Les Newell
2003-12-07 06:02:38 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Egroupscdh (E-mail)
2003-12-07 07:10:42 UTC
RE: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Robert Williams
2003-12-07 07:21:11 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
vavaroutsos
2003-12-07 10:12:41 UTC
Re: Series 1 Bridegport CNC manuals?
Les Newell
2003-12-07 11:13:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
stevenson_engineers
2003-12-07 12:42:56 UTC
Re: Series 1 Bridegport CNC manuals?
Paul
2003-12-07 14:03:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
washcomp
2003-12-07 14:11:36 UTC
Re: Series 1 Bridegport CNC manuals?
Les Newell
2003-12-07 14:26:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Jon Elson
2003-12-07 16:24:58 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Jon Elson
2003-12-07 16:30:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Jon Elson
2003-12-07 16:46:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Hugh Prescott
2003-12-07 20:52:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
vavaroutsos
2003-12-07 21:29:21 UTC
Re: Series 1 Bridegport CNC manuals?
Les Newell
2003-12-08 01:16:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Les Newell
2003-12-08 01:21:15 UTC
Re: [CAD_CAM_EDM_DRO] Series 1 Bridegport CNC manuals?
Larry Van Duyn
2003-12-08 05:30:26 UTC
Re[2]: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Jon Elson
2003-12-08 09:13:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Les Newell
2003-12-19 12:38:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?
Brad Eyben
2003-12-19 18:18:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Series 1 Bridegport CNC manuals?