Re: Controllers
Posted by
Don Rogers
on 2004-03-18 09:06:57 UTC
At 04:27 PM 3/18/2004 +0000, you wrote:
You need a CAM software to get from the drawing to the machine. Try
FreeMill, Ace Converter, Meshcam, or for simple building block parts,
GenGcode. These will all translate the drawings to the Gcode needed to
drive the software controlling the Geckos, or other drivers. Although you
still need to do some text editor work with their output to make sure you
have a usable file. None of these are four axis converters though. To
get to that step, dig out the check book and make sure it is full.
I'm not sure what card you are referring to. Most PC's have a printer port
built in. Use it.
Don
>I have the mill essentially set up. So I guess what I need are the following:Yep
>
>o power supply to supply the 4 Geckos
>o 4 Geckos
>o 4 servo motors
>o 4 encoders
>o Drawing software
>o some kind of card to insert into the motherboard on my PC
>o software to run the card inserted in the motherboard
>
>Am I missing anything ?
You need a CAM software to get from the drawing to the machine. Try
FreeMill, Ace Converter, Meshcam, or for simple building block parts,
GenGcode. These will all translate the drawings to the Gcode needed to
drive the software controlling the Geckos, or other drivers. Although you
still need to do some text editor work with their output to make sure you
have a usable file. None of these are four axis converters though. To
get to that step, dig out the check book and make sure it is full.
I'm not sure what card you are referring to. Most PC's have a printer port
built in. Use it.
Don
Discussion Thread
Don Rogers
2004-03-18 09:06:57 UTC
Re: Controllers
Bob McKnight
2004-03-18 10:05:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepping Motors -indexer
mpkunz
2004-03-18 10:38:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
bull2002winkle
2004-03-18 11:50:58 UTC
Re: Controllers
mpkunz
2004-03-18 15:46:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
Robert Campbell
2004-03-18 15:46:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
rrc62_03782
2004-03-18 15:59:47 UTC
Re: Controllers
Roy J. Tellason
2004-03-18 20:24:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
ballendo
2004-03-18 20:50:59 UTC
The end of pports was Re: Controllers
Trend
2004-03-19 03:49:15 UTC
Re: [CAD_CAM_EDM_DRO] The end of pports was Re: Controllers
Robert Campbell
2004-03-19 05:58:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
Mike Kunz
2004-03-19 06:34:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
james_cullins@s...
2004-03-19 06:44:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
Robert Campbell
2004-03-19 06:59:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Controllers
Henrik Olsson
2004-03-19 10:37:21 UTC
Re: [CAD_CAM_EDM_DRO] The end of pports was Re: Controllers