Re: [CAD_CAM_EDM_DRO] Re: EMC Parallel port config, please help
Posted by
Peter Linss
on 2004-06-02 17:16:32 UTC
Someone recently submitted a patch to EMC that adds configuration of
the parallel port pins via the .ini fine. Expect to see it soon.
the parallel port pins via the .ini fine. Expect to see it soon.
On Jun 2, 2004, at 11:37 AM, Lance Hopper wrote:
> Hey,
> I understand what you are saying, but I can't believe it. The EMC
> is very configurable and customizable. I can't believe it doensn't
> let you reconfigure the pinout of the parallel port. I know about the
> different IO schemes like bridgeportio and minimillio etc... but they
> all seem to be setup basically the same. There has got to be a way,
> but
> all the documentation I've read says nothing about it.
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett <KM6VV@a...>
> wrote:
>> Hi Lance,
>>
>> To change pins around, get a RS-232 type patch box, or wire up a short
>> M-F DB25 cable. About all you can do for EMC, I think. I have the
>> same
>> problem, I wired my drivers for the MaxNC pinout, which has step/dir
>> pins the reverse of EMC's.
>>
>> Alan KM6VV
>>
>>
>> Lance Hopper wrote:
>>> Hello,
>>> Just got BDI TNG (RH7.2 based) EMC running. Trying to hook it up
>>> to an older stepper motor controller. I need to swap some of my
>>> outputs
>>> in EMC to work with my controller. For example, the direction/step
>>> outputs are opposite of what I need (step/dir). I also
>>> need to map my init (turn power on to motors) to pin 16 and high
>>> power (high/low power for when
>>> motors are at rest) to pin 17 etc... The emc.ini file only has
>>> auxillary
>>> stuff like coolant/spindle etc... I don't see anywhere that you can
>>> change step/dir etc.. Any help would be greatly appreciated.
>>>
>>>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach
> it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be
> a sister site to the CCED group, as many of the same members are
> there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
Discussion Thread
Lance Hopper
2004-06-02 11:08:17 UTC
EMC Parallel port config, please help
Alan Marconett
2004-06-02 11:14:44 UTC
Re: [CAD_CAM_EDM_DRO] EMC Parallel port config, please help
Lance Hopper
2004-06-02 11:38:08 UTC
Re: EMC Parallel port config, please help
Peter Linss
2004-06-02 17:16:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Parallel port config, please help
Jon Elson
2004-06-02 22:42:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Parallel port config, please help
Lance Hopper
2004-06-03 04:17:23 UTC
Re: EMC Parallel port config, please help
Jon Elson
2004-06-03 09:15:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Parallel port config, please help
JanRwl@A...
2004-06-03 20:55:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Parallel port config, please help
Lance Hopper
2004-06-04 04:50:15 UTC
Re: EMC Parallel port config, please help
Lance Hopper
2004-06-04 08:59:29 UTC
Re: EMC Parallel port config, please help
Jon Elson
2004-06-04 10:28:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Parallel port config, please help