Re: Troubleshooting a BTR
Posted by
metlmunchr
on 2004-08-07 10:34:57 UTC
I couldn't get to the picture. Does the BTR have onboard memory? If
so, you load the code into BTR memory and run the machine in tape
mode. The function of a BTR is to make the machine think its reading
a tape. Any idea who manufactured the BTR or what name is on it?
From what I've seen, they've been sold under a lot of different names
but actually most were made by just a few companies.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "vinnygenovese"
<superman@r...> wrote:
so, you load the code into BTR memory and run the machine in tape
mode. The function of a BTR is to make the machine think its reading
a tape. Any idea who manufactured the BTR or what name is on it?
From what I've seen, they've been sold under a lot of different names
but actually most were made by just a few companies.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "vinnygenovese"
<superman@r...> wrote:
> I am trying to bring an IKEGIA FX25-N / Fanuc 5T back to life. Thereis a BTR
> that I am trying to bring online. Problem is I don't have anyinstructions or dip
> switch settings. I uploaded a photo tohttp://radiantheat.com/UCM-BTR.jpg.
> The board has a single LED , which seems to 'blink' when i senddata, but it
> seems no signal gets through to the Fanuc 5T. (or I am sending thewrong
> commands). I googled and googled. It seems they are out of business.Any
> hints on the dip switch's or other hints would be very welcome.
>
>
> Vinny \
Discussion Thread
vinnygenovese
2004-08-06 16:47:10 UTC
Troubleshooting a BTR
Jon Elson
2004-08-06 22:25:46 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Stephen Wille Padnos
2004-08-07 10:10:39 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
metlmunchr
2004-08-07 10:34:57 UTC
Re: Troubleshooting a BTR
Alan Marconett
2004-08-07 11:56:44 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Roy J. Tellason
2004-08-07 12:13:45 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Harvey White
2004-08-07 13:43:57 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Roy J. Tellason
2004-08-07 14:02:00 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Alan Marconett
2004-08-07 14:35:16 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Stephen Wille Padnos
2004-08-07 14:39:54 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
Roy J. Tellason
2004-08-07 14:55:50 UTC
Re: [CAD_CAM_EDM_DRO] Troubleshooting a BTR
vinnygenovese
2004-08-08 12:22:46 UTC
Re: Troubleshooting a BTR
metlmunchr
2004-08-08 13:50:35 UTC
Re: Troubleshooting a BTR
Jon Elson
2004-08-08 14:22:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Troubleshooting a BTR
luvindaddy@y...
2004-08-09 13:34:36 UTC
Re: Troubleshooting a BTR
luvindaddy@y...
2004-08-10 06:34:17 UTC
Gateway BTR ....... was Re: Troubleshooting a BTR