CAD CAM EDM DRO - Yahoo Group Archive

Re: laser cnc

on 2004-09-03 02:10:20 UTC
> The emmission technologies website was a good suggestion.
Certainly
> the cheapest (non-ebay) place where you can buy kits or sealed
> tubes. Don't forget the vacuum pump, gas cylinder, regulator, and
> flow valves when you start thinking about building a flowing gas
> laser to save money.


Good point. This is where ebay can come to the rescue again however
a fridge compressor seems to be adequate if you really need to save
the cash.

I would quite like a sealed laser but apart from emmision tech the
other suppliers don't seem all that forth comming over details, much
like the other suppliers of kits. They never seem to show a decent
picture of what you are buying, never mind it actually operating.

If anyone has a good source for sealed CO2 laser tubes that are
known to be of good quality and work then I am interested to find
new sources.

Considering the lack of mass you have to move when making a CNC
laser cutter the CNC part should be a joy to do. Can't wait to get
building.

Graham

Discussion Thread

tfiga221 2004-09-01 07:59:31 UTC laser cnc skykotech 2004-09-01 08:25:56 UTC Re: laser cnc Jones, Joseph A1 2004-09-01 08:53:34 UTC RE: [CAD_CAM_EDM_DRO] Re: laser cnc skykotech 2004-09-01 09:08:17 UTC Re: laser cnc Jones, Joseph A1 2004-09-01 09:19:41 UTC RE: [CAD_CAM_EDM_DRO] Re: laser cnc Stephen Wille Padnos 2004-09-01 09:21:04 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Bob McKnight 2004-09-01 11:34:38 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Roy J. Tellason 2004-09-01 15:47:46 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Graham Stabler 2004-09-01 17:34:26 UTC Re: laser cnc Graham Stabler 2004-09-01 17:38:26 UTC Re: laser cnc skykotech 2004-09-01 18:17:24 UTC Re: laser cnc wanliker@a... 2004-09-01 19:01:46 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Bob McKnight 2004-09-01 20:59:35 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Jon Elson 2004-09-01 21:58:28 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc skykotech 2004-09-01 22:50:49 UTC Re: laser cnc skykotech 2004-09-01 22:57:17 UTC Re: laser cnc terence figa 2004-09-01 23:30:15 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc terence figa 2004-09-02 08:02:06 UTC RE: [CAD_CAM_EDM_DRO] Re: laser cnc skykotech 2004-09-02 08:52:03 UTC Re: laser cnc Tom Hubin 2004-09-02 13:26:49 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Bob McKnight 2004-09-02 21:54:59 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Graham Stabler 2004-09-03 02:10:20 UTC Re: laser cnc josef wagner 2004-09-03 03:19:08 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc Bob Muse 2004-09-03 10:01:13 UTC Re: laser cnc Bob McKnight 2004-09-03 18:17:23 UTC RE: [CAD_CAM_EDM_DRO] Re: laser cnc Bob Muse 2004-09-04 11:29:11 UTC Re: [CAD_CAM_EDM_DRO] Re: laser cnc